GB
100
On-screen Error Messages
Messages Relating to DVD Discs and the HDD
• The following messages appear on the TV screen in case the disc you tried to playback is not appropriate or
the operation is not correct.
CANNOT PLAY BACK THIS DISC.
THIS IS A NON-STANDARD DISC.
REGION CODE OF DISC IS WRONG.
DISC IS NOT INSERTED.
CANNOT OPERATE THIS FUNCTION.
DISC IS PROTECTED.
COULD NOT REPAIR THE DISC.
COULD NOT FINALIZE.
THIS VIDEO IS COPY PROTECTED.
RECORDING IS NOT POSSIBLE.
CANNOT RECORD MORE.
CANNOT RECORD ON THIS DISC.
NO TAPE INSERTED IN DV
CAMCORDER.
CONNECTING TO DV CAMCORDER.
COULD NOT INITIALIZE.
DISC IS FULL.
CANNOT RECORD OR STORE.
THIS VIDEO CANNOT BE RECORDED
TO THIS DISC.
CAN’T DETECT CAMCORDER.
SET THE DATE AND TIME.
• The disc cannot be played back with
this Recorder.
• If you load a disc which cannot be
played with this Recorder (i.e. a
scratched disc), or if you load a disc
upside down, this message will
appear, and the disc tray will
automatically pop out.
• Occurs if you load a DVD disc whose
region number is not “ALL” or whose
region number does not contain “2”.
• Occurs if no disc is loaded in the disc
tray.
• Occurs if operation is incorrect.
• Occurs if you attempt to record or edit
a disc for which disc protection is set.
• Occurs if you attempt DV input of
video which cannot be recorded, and
attempt to record to a DVD.
• If there is a power failure during DVD
recording, the system automatically
tries to recover data after power is
restored. This error occurs if such
recovery is impossible.
• Occurs if the disc is scratched or
dirty, etc.
• Occurs if video with a copy guard
signal is input.
• Occurs if a title or chapter mark
exceeds the recordable upper limit.
• Number of titles: HDD 199/DVD 99.
Number of chapters: HDD 999/
DVD 999
• Occurs if you load a disc which cannot
be recorded to with this Recorder, or a
disc which is scratched or dirty.
• Occurs if you attempt operation when a
tape has not been loaded in the digital
camcorder linked via DV connection.
• Occurs if the digital camcorder power
goes off or the cable is pulled out
while connecting to DV.
• Occurs if connection with the digital
camcorder is broken.
• Occurs if the disc is scratched or
dirty, etc.
• Occurs if there is no empty space in
the disc.
• Occurs if you try to record a “Copy
Once” broadcast onto a disc which is
not compatible with CPRM.
• Occurs if you set to DV input without
connecting a digital camcorder.
• Occurs if multiple digital camcorders
are connected.
• Occurs if timer programming is done
when the Recorder clock has not
been set.
• Check the disc, and load it correctly.
• Cancel disc protection, or reload a
recordable disc.
• Check the disc, and load it correctly.
• Cannot record.
• Erase unnecessary titles.
• Either erase unnecessary chapters, or
combine chapters.
• Reload an appropriate recording
disc.
• Load a tape into the digital
camcorder.
• Check the power of digital camcorder
or cable connection.
• System is performing reconnection
processing. Wait about 30 seconds.
• Check the disc, and load it correctly.
• Load a disc with empty space.
• Erase unnecessary titles.
• Load a CPRM compatible disc (DVD-
RW Ver. 1.1 or higher) initialized in VR
mode.
• Connect a digital camcorder, and
reset again to DV input.
• Set the clock and perform timer
programming again.
Error message
Possible Error
Suggested Solution
Continued on Next Page
|||
DV-HR350F-097-106
04.3.1, 4:28 PM
100