Sharp AR-PB2A, Руководство по обслуживанию

Страница: 28 / 40

Setting Behavior
Automatic
Switching Between
Jobs When receiving data is detected through
a port, sensing data receipt from each
port, considers the port as current (port
automatic sensing processing), and
processes the data received only through
the current port. Then until the job ends
in the situation described below in 1) or
2), the data through the current port is
only processed. After the print job ends,
the port automatic sensing processing
restarts.
1) The print job is completed by the
job-end command.
2) The current port gets into the state of
waiting for data receipt, and after no
data is received for a certain time (I/O
time-out value), print job ends by the
I/O time-out.
After I/O
Time-out When receiving data is detected through
a port, sensing data receipt from each
port, considers the port as current (port
automatic sensing processing) and
processes the data received only through
the current port. Then until the I/O
time-out in the situation described below
in 1), the data through the current port is
only processed. After the I/O time-out,
the port automatic sensing processing
restarts.
1) The current port gets into the state of
waiting for data receipt, and after no
data is received for a certain time (I/O
time-out value), the print job ends by
the I/O time-out. (When the print job
has not been completed , it ends
simultaneously.
Fixed Disables
P1284 Port Receives data only through the Network
(NIC) port.
Disables
Network
(NIC) Port Receives data only through the P1284
port.
Note: In the I/O time-out, the count starts at the point that data is not
acquired via the receiving buffer. When receiving the data until
the I/O time-out, the count is reset to stop.
In the between jobs setting of the automatic switching, the
conditions that a print job will be completed are as follows.
Job Start Job End
Common • PJL JOB command
↔
• PJL EOJ command
• I/O Timeout
PCL • PJL ENTER
LANGUAGE
command (PCL)
• Jobs starting with the
PCL data
↔
• UEL command
• <ESC>E
• I/O Timeout
PS • PJL ENTER
LANGUAGE
command
(POSTSCRIPT)
• Jobs starting with the
PostScript data.
↔
• UEL command
• <Ctrl-D>
• I/O Timeout
[Example of Automatic Switching]
Receiving Port Job End Data
Job1: NIC Port Yes
Job2: 1284 Port No
Job3: NIC Port Yes
1) Automatic Switching - Between Jobs
2) Automatic - After I/O Time Out
13. Memory Configuration
The following ROM are supported.
EPROM: Boot & Simulation Program
Flash ROM: Program &Font data
Boot ROM is selectable between EPROM and Flash ROM #5 using
the jumper switching.
Flash ROM #5 4MB Main Program
Flash ROM #5 3MB PCL Roman 80 Fonts
PS Roman 80 Fonts
Flash ROM #5 1MB Boot/Simulation Program
14. Printer control PWB switch (short pin)
and LED display
Switch, LED Function
Switch RESET switch
(SW102) Processor and peripheral device
initialization
ABORT switch
(SW101) MMI* generation to processor
LED POWER-LED
(D114) PWB power ON. Lighted when
supplying power.
RUN-LED
(D113) Processor operating status.
Lights up when operating.
Software
status STO-LED
(D109) Lights UPD71055-A port 0 bit 4 at
"0."
ST1-LED
(D110) Lights UPD71055-A port 0 bit 5 at
"0."
ST2-LED
(D111) Lights UPD71055-A port 0 bit 6 at
"0."
ST3-LED
(D112) Lights UPD71055-A port 0 bit 7 at
"0."
Job End Data
Wait
1284
NIC Job1
Receive Job1
Receive Job3
Job2
Job3
Receive Job2
Receive to Buffer
I/O Timeout
1284
NIC
Job1
Receive Job1
Receive Job3
Receive Job2
Job2
Job3
I/O Timeout
I/O Timeout
Receive to Buffer
AR-PB2A
7 – 4