Sharp AR-PB2A, Руководство по обслуживанию

Страница: 26 / 40

2. Printer Operation / Message Display
State Display
JOB
Cancel/(Clear)
Paper Selection
Online
LED
Data
LED
During initializing the printer board <Displayed on dialog window>
INITIALIZING. PLEASE WAIT. Disabled Off Off
From the end of initialization to the end of warm-up. WARMING UP. PLEASE WAIT Disabled Off Off / On
During the warm-up and waiting for starting a print job with
the data receiving /processing completed PLEASE WAIT. Disabled On On
During the idle
(Online with no data being received / printed) READY TO PRINT.) Disabled On Off
During receiving the data
During processing the data
During transferring images to ERDH PROCESSING PRINT DATA. Disabled On Blink
During the output of print
(during printing the data stored in ERDH) PRINTING IN PROGRESS. Disabled On Blink
During suspending the print
(from when the print starts to be suspended by user’s
instruction during printing and to when the print job can be
actually stopped. <Displayed on a dialog window>
PRINTING IN PROGRESS.
PLEASE WAIT. Disabled Blink Blink
While the print is suspended by user.
(the data is held) OFFLINE.
TO CLEAR DATA, PRESS [C]. Enabled Off On
While the print data is being cleared.
(Job Cancel) PLEASE WAIT.
DATA IS BEING CLEARED. Enabled Off On
Offline
(The state in which no data is being received and printed,
and the user instruction causes Offline.) OFFLINE. Disabled Off Off
When there is no paper in Bypass Tray during suspending
a job with Bypass Tray (manual) selected.
(The data is held.) ADD ******** PAPER INTO BYPASS-TRAY.
(When supplying paper as directed, the print
will start in three seconds. However, since
the size detection is not performed, the
paper sizes other than selected one will start
to be printed.) Enabled Off On
When there is paper in Bypass Tray during suspending a
job with Bypass Tray (manual) selected.
(The data is held.) CHANGE BYPASS-TRAY PAPER TO
********.
(When supplying paper as directed, the print
will start in three seconds. Even if the paper
in bypass tray continues to be used , the
paper needs to be reset by loading it again.
However, since the size detection is not
performed, the paper sizes other than
selected one will start to be printed.) Enabled Off On
When there is no paper in Bypass Tray selected at the start
of printing the data, or when the print is suspended due to
paper-out.
(The data is held.) ADD ******** PAPER INTO BYPASS-TRAY.
(When supplying paper as directed, the print
will automatically restart in three seconds.) Enabled Off On
When there is no paper in the selected tray at the start of
printing the data, or when the print is suspended due to
paper-out.
(The data is held.) OPEN * TRAY AND ADD PAPER.
(When supplying paper as directed, the print
will automatically restart after the lift-up
operation in the tray.) Enabled Off On
When Staple Unit is not installed properly
(the data is held) CHECK STAPLER POSITION OR STAPLE
JAM.
(When checking and setting properly as
directed, the print will automatically restart.) Enabled Off On
When a stapler is empty (AR-FN1)
(The data is held.) SLIDE THE FINISHER AWAY FROM THE
COPIER AND ADD STAPLES.
(when checking and setting properly as
directed, the print will automatically restart.) Enabled Off On
When a stapler is empty (AR-FN2)
(The data is held) ADD STAPLES.
(When checking and setting properly as
directed, the print will automatically restart.) Enabled Off On
During suspending the print due to some errors
( Jam/Toner supply)
(The data is held) <CONFORM TO COPIER OPERATION
SPECIFICATION.>
(Print will start just as the trouble is removed.) Disabled Off On
AR-PB2A
7 – 2