manualshive.com logo in svg

Sharp AR-M351N, Руководство по обслуживанию

"Sharp AR-M351N" - высококачественный многофункциональный принтер с функцией копирования и сканирования. Инструкция по эксплуатации доступна для загрузки бесплатно на manualshive.com. Получите руководство по эксплуатации и настройке этого устройства для удобства использования и поддержания его в хорошем состоянии.

Поделиться
Скачать
background image

AR-M351U/M451U, AR-M355U/M455U  TROUBLE CODES  11 - 9

F7

01

Content

FAX board EEPROM read/write error

Details

EEPROM access error (read/write)

Cause

EEPROM trouble
FAX PWB EEPROM access circuit 
trouble

Check & 
Remedy

When replacing the EEPROM, use 
SIM66-4/5 (Signal send level)  and 
SIM66-14/15/16 (Dial test) for 
adjustment. However, note that all the 
soft switches are reset to the initial 
values.
No need to adjust when the PWB is 
replaced.

H2

00···

HL1

01···

HL2

Content

Thermistor open
Fusing unit not installed

Detail

Thermistor is open. 
(An input voltage of 2.92V or above is 
detected.)
Fusing unit not installed

Cause

Thermistor trouble
Control PWB trouble
Fusing section connector 
disconnection
AC power trouble
Fusing unit not installed

Check and 
remedy

Check harnesses and connectors from 
the thermistor to the control PWB.
Use SIM14 to clear the self diag 
display.

H3

00···

HL1

01···

HL2

Content

Fusing section high temperature 
trouble

Detail

The fusing temperature exceeds 
242°C. (An input voltage of 0.27V or 
above is detected.)
Fusing temperature control is started, 
and 242°C is detected three or more 
times continuously in sampling in the 
specified interval. (Every 300msec) 

Cause

Thermistor trouble
Control PWB trouble
Fusing section connector 
disconnection
AC power trouble

Check and 
remedy

Use SIM5-2 to check the heater lamp
Blinking operation.

If the heater lamp blinks normally:
Check the thermistor and its 
harness.
Check the thermistor input circuit in 
the control PWB.

If the heater lamp keep lighting:

Check the AC PWB and the lamp 
control circuit in the control PWB.
Use SIM14 to cancel the trouble

MAIN SUB

Details

H4

00···

HL1

01···

HL2

Content

Fusing section low temperature trouble

Detail

The set temperature is not reached 
within the specified time (3 min) after 
turning on the power relay, or the 
temperature does not reach 80°C 
within 80 sec.
When the heater lamp is not turned off 
in the specified time (3 min) from 
starting warm-up, or the temperature 
does not reach 80°C within 80 sec.
After completion of warm-up operation, 
a temperature 50°C lower than the 
temperature control level is detected 5 
times continuously in sampling in the 
specified interval. (every 300msec)

Cause

Thermistor trouble
Heater lamp trouble
Control PWB trouble
Thermostat trouble
AC power trouble
Interlock switch trouble

Check and 
remedy

Use SIM5-2 to check the heater lamp
Blinking operation.

If the heater lamp blinks normally:
Check the thermistor and its 
harness.
Check the thermistor input circuit in 
the control PWB.

If the heater lamp does not light:

Check for heater lamp disconnection 
and thermostat disconnection.
Check the interlock switch.
Check the AC PWB and the lamp 
control circuit in the control PWB.
Use SIM14 to cancel the trouble.

H5

01

Content

5-time continuous POD1 not-reaching 
jam detection

Detail

5-time continuous POD1 not-reaching 
jam detection

Cause

A fusing section jam is not properly 
removed. (Jam paper remains.)
POD1 sensor trouble, or harness 
disconnection
Improper installation of fusing unit

Check and 
remedy

Check jam paper in the fusing section. 
(winding, etc.)
Check POD1 sensor harness, and 
check  the fusing unit installation.
Use SIM14 to cancel the trouble.

L1

00

Content

Scanner feed trouble

Details

Scanner feed is not completed within 
the specified time.

Cause

Scanner unit abnormality
Scanner wire disconnection

Check & 
Remedy

Check scanning with SIM 1-1.

L3

00

Content

Scanner return trouble

Details

Scanner return is not completed within 
the specified time.

Cause

Scanner unit abnormality
Scanner wire disconnection

Check & 
Remedy

Check scanning with SIM 1-1.

MAIN SUB

Details

Содержание AR-M351N





















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AR-M351N

Eaton Power Defense PD3 Mounting And Operating Instructions preview
Power Defense PD3
Бренд: Eaton Страницы: 4
Canon imageRUNNER 2545i Addendum Manual preview
imageRUNNER 2545i
Бренд: Canon Страницы: 37
Konica Minolta Bizhub 4020 Shortcut Manual preview
Bizhub 4020
Бренд: Konica Minolta Страницы: 40
Oki C911dn Supplementary Manual preview
C911dn
Бренд: Oki Страницы: 44
Tally t2145 Operator'S Manual preview
t2145
Бренд: Tally Страницы: 106
SAGEMCOM Agoris M943 User Manual preview
Agoris M943
Бренд: SAGEMCOM Страницы: 146
MIMAKI UJF-605R II Daily Care Manual preview
UJF-605R II
Бренд: MIMAKI Страницы: 28
Triumph Adler DC 2025 Instruction Handbook Manual preview
DC 2025
Бренд: Triumph Adler Страницы: 139
IBM 3852-2 Hardware Reference Manual preview
3852-2
Бренд: IBM Страницы: 128
SATO M-8450 Operator'S Manual preview
M-8450
Бренд: SATO Страницы: 241
Tally T9020 Maintenance Manual preview
T9020
Бренд: Tally Страницы: 54
Samsung SCX-4623F Specifications preview
SCX-4623F
Бренд: Samsung Страницы: 2
Samsung SCX-4623 Series Quick Install Manual preview
SCX-4623 Series
Бренд: Samsung Страницы: 2
Samsung SCX-4600 Series Specifications preview
SCX-4600 Series
Бренд: Samsung Страницы: 2
Samsung SCX-4600 Series Brochure & Specs preview
SCX-4600 Series
Бренд: Samsung Страницы: 5
Samsung SCX-4321NS series Quick Installation Manual preview
SCX-4321NS series
Бренд: Samsung Страницы: 2
Samsung SCX-4521FG - B/W Laser - All-in-One License Agreement preview
SCX-4521FG - B/W Laser - All-in-One
Бренд: Samsung Страницы: 28
Samsung SF4500 User Manual preview
SF4500
Бренд: Samsung Страницы: 93

Бренды по названию

Популярные бренды

Загрузить еще бренды