Sharp AR-BC260 Скачать руководство пользователя страница 116

Страница: 116 / 184

IMAGE EDIT MENU

6-20

Touch the [MULTI SHOT] key on the
IMAGE EDIT menu screen.

The MULTI SHOT
setting screen will
appear.
The multi shot icon (

etc.) will also appear in
the upper left of the
screen to indicate that
the function is turned on.

Select the number of originals to be
copied onto one sheet of copy paper on
the multi shot selection screen.

The orientation of copy paper and the image of the
originals may be rotated as needed.

Select the layout.

Select the order in which
the originals will be
arranged on the copy.

The arrows in the above diagram indicate the
directions in which the images are arranged.

Select whether or not to add borderlines.

When the BORDER
LINE checkbox is
selected, borderlines
are added around the
borders of the images.

Touch the [OK] key (inside [OK] key) on
the MULTI SHOT setting screen.

Return to the IMAGE EDIT menu screen.

Touch the [OK] key on the IMAGE EDIT
menu screen.

Return to the SPECIAL MODES screen.

Touch the [OK] key on the SPECIAL
MODES screen.

Return to the main screen of copy mode.

MULTI SHOT

OPY

CANCEL

IMAGE EDIT

MULTI SHOT

2in1

4in1

LAYOUT

BORDER LINE

CANCEL

LAYOUT

BORDER

2in1

4in1

Shot number

Layout

About the steps that follow

If a reversing single pass feeder is being used,
see pages 5-2 through 5-6. If the document
glass is being used, see pages 5-7 through 5-9.

To cancel the multi shot function, touch the
[CANCEL] key on the multi shot setting screen (step
2).

CANCEL

YOUT

BORDER LINE

ApollonII_general-copy_SEC.book 20

ページ

２００４年９月６日　月曜日　午後４時５７分

Содержание AR-BC260

























































































































































































Результаты поиска

Содержание AR-BC260

Отзывы:

Sharp AR-BC260, Руководство по эксплуатации, Страница: 116 / 184

Результаты поиска

Содержание AR-BC260

Отзывы: