Sharp AR-BC260 Скачать руководство пользователя страница 100

Страница: 100 / 184

SPECIAL MODES

6-4

Margin shift

The margin shift function will automatically shift the text or image on the copy paper approximately 1/2" (10 mm) in
its initial setting.

Touch the [MARGIN SHIFT] key on the
SPECIAL MODES screen.

The margin shift setting
screen will appear.
The margin shift icon
(

) will also appear in

the upper left of the
screen to indicate that
the function is turned on.

Select the shift direction.

Touch a shift direction
key to select right or left.
The selected key will be
highlighted.

Set the shift amount as needed and touch
the [OK] key.

Use the

and the

keys to set the shift
amount. The shift amount
can be set from 0" to 1" in
1/8" increments.

If a duplex module/2 x
500 sheet paper drawer

and duplex bypass/inverter unit are not installed,
the margin shift setting for back-side copies will
not be displayed.

Touch the [OK] key on the SPECIAL
MODES screen.

Return to the main screen of copy mode.

●

The shift direction can be selected from right or left shift as
shown in the illustration.

One-sided copying

Original

Image shifted
to the right

Margin

Two-sided copying

Original

Margin

Image shifted
to the left

Image shifted
to the right

Image shifted
to the left

MARGIN SHIFT

CENTERING

RIGHT

LEFT

About the steps that follow

If a reversing single pass feeder is being used,
see pages 5-2 through 5-6. If the document
glass is being used, see pages 5-7 through 5-9.

To cancel the margin shift function, touch the
[CANCEL] key on the margin shift setting screen.

SIDE 1

(0 1)
inch

SIDE 2

CANCEL

1/2

ApollonII_general-copy_SEC.book 4

ページ

２００４年９月６日　月曜日　午後４時５７分

Содержание AR-BC260

























































































































































































Результаты поиска

Содержание AR-BC260

Отзывы:

Sharp AR-BC260, Руководство по эксплуатации, Страница: 100 / 184

Результаты поиска

Содержание AR-BC260

Отзывы: