Sharp AR-BC260 Скачать руководство пользователя страница 108

Страница: 108 / 184

COLOR ADJUSTMENTS MENU

6-12

RGB adjust

Strengthens or weakens one of three primary colors, red (R), green (G), or blue (B).

Touch the [RGB ADJUST] key on the
COLOR ADJUSTMENTS menu screen.

Select a color from R (RED), G (GREEN),
and B (BLUE).

Only one primary color can be adjusted.

Adjust the selected color.

Touch the [+] to
strengthen the selected
color or touch the [-] key
to weaken the color.

When the key is touched, the color adjustments
menu icon (

) will appear at the upper left of the

screen to indicate that the function is turned on.

Touch the [OK] key (inside [OK] key) on
the RGB ADJUST setting screen.

Return to the COLOR ADJUSTMENTS menu
screen.

Touch the [OK] key on the COLOR
ADJUSTMENTS menu screen.

Return to the SPECIAL MODES screen.

Touch the [OK] key on the SPECIAL
MODES screen.

Return to the main screen of copy mode.

OLOR ADJUSTMENTS

RGB ADJUST

COLOR

BALANCE

RGB ADJUST

COLOR
ADJUSTMENTS

ONLY ONE COLOR CAN BE ADJUSTED.

R(RED)

G(GREEN)

B(BLUE)

CANCEL

-2

-1

CANCEL

-2

-1

About the steps that follow

If the reversing single pass feeder is being
used, see pages 5-2 through 5-6. If the
document glass is being used, see pages 5-7
through 5-9.
In either case, press the [COLOR COPY
START] key to begin copying.

To cancel the RGB ADJUST function, select the
RGB ADJUST function again and touch the
[CANCEL] key (step 2 or 3).

sec_apollon_06-1.fm 12

ページ

２００４年１１月１５日　月曜日　午前１１時４５分

Содержание AR-BC260

























































































































































































Результаты поиска

Содержание AR-BC260

Отзывы:

Sharp AR-BC260, Руководство по эксплуатации, Страница: 108 / 184

Результаты поиска

Содержание AR-BC260

Отзывы: