Sharp AR-164 Скачать руководство пользователя | Manualshive

Страница: 16 / 80

background image

14

MAKING COPIES

NORMAL COPYING

Using the SPF

Stream feeding mode

If the stream feeding mode has been enabled using user program
No. 4, the SPF indicator will continue to blink for approximately
5 seconds after feeding of all originals is completed. While this
indicator is blinking, any new originals placed in the SPF will be
fed and copied automatically. See page 46, USER PROGRAMS.

1

Turn the power switch on.

●

It will take about 35 seconds for the copier to warm up. However, you
can make desired settings and press the START key during warm-up.
Copying will start after warm-up.

●

If the copier has been programmed in the auditing mode, the START
key indicator will not light up and “

– – –

” will appear in the copy

quantity display. Enter an assigned 3-digit account number. See page
13.

●

If the power is already on and all indicators except the POWER SAVE
indicator are off, the copier is in the auto power shut-off mode. Press
the START key in this case. See page 53, POWER SAVE MODES.

2

Ensure that no original is left on the original table.

3

Adjust the original guides to the size of the originals.

4

Set the originals face up in the document feeder tray.

●

The SPF indicator will light up. If this indicator does not light up, the
originals are not properly set or the SPF is not properly closed.

5

Ensure that the copy paper size in the paper tray is the
same size as the originals.

●

If an optional paper feed unit is installed, a paper tray with the
corresponding paper size will be automatically selected.

Normal copying

This copier has two document input stations –– a single pass
feeder (SPF) for automatic document feeding and an
original table for manual handling of bound documents.
The SPF is designed to hold up to 30 originals measuring
from 5-1/2" x 8-1/2" to 11" x 17" and in the weight range of
15 to 24 lbs.

●

Be sure to remove any staples or paper clips from the
originals.

●

Damaged or crumpled originals may misfeed in the SPF.
It is recommended that these originals be copied from the
original table.

●

Before placing curled or wavy originals into the document
feeder tray, be sure to flatten them. If not, original misfeeds
may result.

●

For best feeding of originals which have binding holes
punched into them, insert them so that the holes are
positioned to the right or along the side guides.

●

Special originals such as transparency film and tracing
paper should not be fed through the SPF but should be
copied from the original table.

Power on

«
...
14
15
16
17
18
...
»

Содержание AR-164

















































































Отзывы:

Нет отзывов

Похожие инструкции для AR-164

Бренд: Xerox Страницы: 16

DocuColor DocuColor 4

Бренд: Xerox Страницы: 166

Бренд: Kyocera Страницы: 44

Бренд: Olivetti Страницы: 18

Бренд: Xerox Страницы: 2

IMAGERUNNER 2016

Бренд: Canon Страницы: 2

Бренд: Lanier Страницы: 184

Бренд: ADAMS Evidence Grade Technology Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды