Sharp AQUOS LC-70LE633U Скачать руководство пользователя страница 9

Страница: 9 / 60

LC-70LE632U/633U

3 – 2

2.2.3 How to upgrade the software

1. Unplug the AC cord.

2. Insert the USB Memory for version upgrade into the service socket.

3. Plug in the AC cord with power button pressed down.

4. After 5 seconds, unpress the power button.

5. After the unit startup, the system upgrade screen as shown below within 20-40 seconds.

6. Even a single failure in the process will trigger the upgrade failure screen.

NOTE: In the event of a failure, repeat the upgrade process. If the process repeatedly fails, it is likely that the hardware need fixing.

7. Upon completion of the whole process, the upgrade success screen as shown below appears. You can check the new software version on this

screen. The version information appears after the upgrade is complete.

8. Unplug the AC cord and remove the USB Memory for version upgrade.

9. Now the software version upgrade is complete.

NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the main

software version information.

MAIN

SUB MICOM

PANEL EEPROM

IR MICOM

MAIN Version

SUB MICOM Version

PANEL EEPROM

IR MICOM Version

50%

NO DATA

U1007071

㧙㧙㧙㧙㧙

㧙㧙㧙㧙

1.00

70LE632U

Software Update

MAIN

UPGRADE FAILURE

SUB MICOM

PANEL EEPROM

IR MICOM

MAIN Version

SUB MICOM Version

PANEL EEPROM

IR MICOM Version

Project ID

NO DATA

㧙㧙㧙㧙㧙

㧙㧙㧙㧙

1.00

70LE632U

Software Update

MAIN

UPGRADE SUCCESS

SUB MICOM

PANEL EEPROM

IR MICOM

MAIN Version

SUB MICOM Version

PANEL EEPROM

IR MICOM Version

100%

NO DATA

U1007071

㧙㧙㧙㧙㧙

㧙㧙㧙㧙

1.00

70LE632U

Software Update

Содержание AQUOS LC-70LE633U





























































Результаты поиска

Содержание AQUOS LC-70LE633U

Отзывы:

Похожие инструкции для AQUOS LC-70LE633U

Бренды по названию

Популярные бренды

Sharp AQUOS LC-70LE633U, Руководство по обслуживанию

Результаты поиска

Содержание AQUOS LC-70LE633U

Отзывы:

Похожие инструкции для AQUOS LC-70LE633U

Бренды по названию

Популярные бренды