Sharp AQUOS LC-70LE633U Скачать руководство пользователя страница 19

Страница: 19 / 60

LC-70LE632U/633U

3 – 12

8.2.5 Component 33K signal adjustment

8.2.6 Analog RGB signal adjustment

8.2.7 Tuner/V-CHIP adjustment

Adjustment point

Adjustment conditions

Adjustment procedure

Setting

1080i signal

•

Send the 100% color bar signal to the component input.

Automatic adjustment exe-
cution

Point the cursor to [ COMP33K ADJ(INPUT1)] and press the [Enter] key.
The adjustment is complete when [ COMP33K ADJ(INPUT1) OK] is displayed.

Adjustment point

Adjustment conditions

Adjustment procedure

Setting

Signal: XGA
(1024x768) 60Hz
SYNC: HV separate

• Send the 100% color bar signal to the PC input.

Automatic adjustment exe-
cution

Point the cursor to [ ANALOG RGB ADJ] and press the [Enter] key.
The adjustment is complete when [ ANALOG RGB ADJ OK] is displayed.

Adjustment point

Adjustment conditions

Adjustment procedure

Setting

NTSC RF signal
US-7(AIR)ch

• Send the NTSC signal to the RF antenna input.

Automatic adjustment exe-
cution

Point the cursor to [ VCHIP TEST(*07ch)] and press the [Enter] key.
(* Adjust the selected channel to the in-house signal.)
The adjustment is OK when [ VM-OK] is displayed in green.
(NG when VM-NG is displayed in red.)

100% white

0% black

1080i
100% color bar

Color saturation: 100%

100% white

0% black

XGA (1024x768)
100% color bar

Содержание AQUOS LC-70LE633U





























































Результаты поиска

Содержание AQUOS LC-70LE633U

Отзывы:

Похожие инструкции для AQUOS LC-70LE633U

Бренды по названию

Популярные бренды

Sharp AQUOS LC-70LE633U, Руководство по обслуживанию

Результаты поиска

Содержание AQUOS LC-70LE633U

Отзывы:

Похожие инструкции для AQUOS LC-70LE633U

Бренды по названию

Популярные бренды