Sharp Aquos LC-60LE631M, Руководство по эксплуатации

Страница: 17 / 28

15
NOTE
• For resetting all adjustment items to the factory preset
values, press
a
/
b
to select “Reset”, press ENTER , press
c
/
d
to select “Yes”, and then press ENTER .
• Images may not be displayed properly depending on the
settings and/or input signals.
Input signal
• Some input signals may have to be registered
manually to display properly.
• The pairs of input signals (resolutions) in the list
below are not distinguishable when received.
In such case, you have to set the correct signal
manually. After setting once, it will display when the
same signal (resolution) is input again.
1280
g
768 1360
g
768
H
DivX(R) Reg. Code
Please see page 21.
H
Version up
This function is only for service personnel to use for
software updates.
Picture and still image
You can freeze a motion picture on the Display.
1
Press FREEZE .
• A still image displays.
2
Press RETURN again to exit still image.
NOTE
• The still image automatically goes out after 30 minutes.
• FREEZE doesn’t function for PC input (all resolution).
Wide Mode
Auto Selection
If you set “WSS” and “4:3 mode” in the Setup menu,
the optimum WIDE mode is automatically chosen for
every broadcast containing the WSS information.
“WSS” menu
To enable Auto Selection, set “WSS” in the Setup
menu to “On”. (See page 13.)
“4:3 mode” menu
To set the type of the wide screen, select “Panorama”
or “Normal” in the 4:3 mode menu. (See page 13.)
4:3 mode set to “Panorama” 4:3 mode set to “Normal”
NOTE
• If the broadcast signal contains no WSS information, Auto
Selection will not function even when the WSS option is
enabled.
Option menu (Continued)
H
Game play time
This function displays the elapsed game time so you
do not lose track of the time.
To display the elapsed time, select “GAME” under
“AV mode” for the input mode of the terminal
connected to the game console before starting the
game.
Selected item Description
On The elapsed time is displayed every 30
minutes when you switch to GAME mode
in external input mode.
Off Hides the time.
H
Colour system
You can change the colour system to one that is
compatible with the image on the screen. (Auto,
PAL, SECAM, NTSC 3.58, NTSC 4.43, PAL-60)
NOTE
• If “Auto” is selected, colour system for each channel is
automatically set. If an image does not display clearly,
select another colour system (e.g. PAL, NTSC 4.43).
• “Colour system” is selectable only when inputting a
composite signal.
H
Fine sync. (PC input mode only)
Adjusting the PC image automatically
Auto sync.
This function enables the screen to be automatically
adjusted to its best possible condition when the
analogue terminals of the TV and PC are connected
with a commercially available RGB cable, etc.
NOTE
• Auto sync. is likely to succeed when an input PC image
has wide vertical stripes (e.g. pattern with high contrast
stripes, or cross-hatched).
It may fail when an input PC image is solid (low contrast).
Adjusting the PC image manually
Ordinarily you can easily adjust the picture as
necessary to change image position using Auto
sync. In some cases, however, manual adjustment is
needed to optimise the image.
Selected item Description
H-Position Centres the image by moving it to the left
or right.
V-Position Centres the image by moving it up or
down.
Clock Adjusts when the image fl ickers with
vertical stripes.
Phase Adjusts when characters have low
contrast or when the image fl ickers.
LC-60LE631M_EN 662.indd 15 LC-60LE631M_EN 662.indd 15 10/2/2012 11:31:30 AM 10/2/2012 11:31:30 AM