Sharp AQUOS LC-37BG1E, Руководство по эксплуатации

Страница: 10 / 42

8
Quick guide
Turning on the power
Press
a
on the TV.
NOTE
• If you are not going to use this TV for a long period of time,
be sure to remove the AC cord from the power outlet.
• Weak electric power is still consumed even when a is
turned off.
• In DTV input mode, if the power is turned off immediately
after a setting change from the menu screen, the new
setting or channel information may not be memorised.
Initial auto installation (Analogue)
When the TV powers on for the fi rst time after
purchase, the initial auto installation (Analogue) is
invoked. Follow the menus and make the necessary
settings one after another.
NOTE
• To reconfi gure the initial auto installation settings, go to
“Channels” and run “Search wizard” from the Setup menu.
(Page 16)
Setting the on-screen display language
1
Press
a
/
b
/
c
/
d
to select the desired language
listed on the screen.
2
Press
OK
to enter the setting.
Setting the country (“Location of TV set” screen)
1
Press
a
/
b
/
c
/
d
to select your country or area
listed on the screen.
2
Press OK to enter the setting.
• An overview of settings to be used for auto search
displays.
Press OK to start the search.
• The TV searches for, sorts and stores all the
receivable TV stations according to their settings and
the connected antenna.
• To abort the initial auto installation in progress, press
END .
When the auto sorting is completed, the item
“Decoder” displays. Press
c
/
d
to select “EXT
1” or “EXT 2”, and then press OK .
• Make sure to select the terminal (EXT 1 or 2) to which
the decoder is connected.
A message appears indicating that the fi rst
installation is successfully completed. Press
OK , if necessary.
• If a recording device with AV-Link is connected to
EXT 2, the TV automatically starts transferring the
station list data to the recording device.
1
2
3
4
5
Standby mode
Press
B
on the remote control unit when the TV is on.
• The TV enters standby mode and the image on the screen
disappears.
• The B indicator on the TV changes from green to red.
• To completely turn off the power to the TV, unplug the AC
cord from the AC outlet. However, do not unplug the AC
cord unless otherwise instructed.
Off
Display status indicator
Power off
Initial auto installation (DTV)
Digital Video Broadcasting is a transmission scheme.
It is much more than a simple replacement for existing
analogue television transmission. DVB provides more
stations, clearer picture quality and other services
displayed on the screen. It also allows a range of new
features and services including subtitles and multiple
audio tracks.
To watch DTV broadcasts, follow the procedures below
to scan all available services in your area.
NOTE
• Make sure to perform Initial auto installation
(Analogue) outlined in the preceding section as well,
even if you intend to view only DTV broadcasts.
Press DTV (or
b
, then
a
/
b
to select “DTV”,
and then press OK ) to access the DTV mode.
Press DTV MENU and the DTV Menu screen
displays.
Press
c
/
d
to select “Installation”.
Press
a
/
b
to select “Auto Installation”, and
then press OK .
If you have already set the PIN, enter it here. If
not, enter the factory preset PIN “1234”.
• See page 17 for setting PIN.
• A confi rmation message displays. Press
c
/
d
to
select “Yes”, and then press OK to start the search.
The TV starts scanning all available DTV and
radio services in your area.
NOTE
• The language and country settings used in this operation
are the settings you have already set while executing
the
Initial auto installation (Analogue) . If you want to
reconfi gure the country setting, for instance after moving
to another country, conduct “Search wizard” from the
Analogue Menu again. (Page 16)
• The DTV services are searched and stored according to the
channel number information embedded in the TV signal (if
available). If the information is not available, the services are
stored according to the order in which they were received.
If you would like to sort the order, it is possible to arrange it
as explained in page 25.
• To cancel the scan in progress, press END .
• You cannot select any DTV-related menu items unless “Auto
Installation” has been completed.
1
2
3
4
5
Green
Red
The TV is in standby mode.
The TV is on.
LC-42BG1E_gb_a.indd 8 LC-42BG1E_gb_a.indd 8 2007/05/23 13:49:00 2007/05/23 13:49:00