ELECTRICAL ADJUSTMENTS
D-1
1. ADJUSTMENT PROCEDURE
Read and perform these adjustments when repairing the
circuits or replacing electrical parts or PCB assemblies.
CAUTION
On-Screen Display Adjustment
1.
2.
Set the VOLUME to minimum.
Press the VOL. DOWN button on the set and the
channel button (9) on the remote control for more than
2 seconds to display adjustment mode on the screen as
shown in Fig. 1-1.
Fig. 1-1
FUNCTION
H POSI OSD
V POSI OSD
R DRIVE (M)
R CUTOFF (M)
G DRIVE (M)
G CUTOFF (M)
B DRIVE (M)
B CUTOFF (M)
R DRIVE (M)
R CUTOFF (H)
G DRIVE (H)
G CUTOFF (H)
B DRIVE (H)
B CUTOFF (H)
R DRIVE (L)
R CUTOFF (L)
G DRIVE (L)
G CUTOFF (L)
B DRIVE (L)
B CUTOFF (L)
H POSI
H POSI MAX
NO.
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
•
•
•
Use an isolation transformer when performing any
service on this chassis.
When removing a PCB or related component, after
unfastening or changing a wire, be sure to put the wire
back in its original position.
When you exchange IC and Transistor with a heat sink,
apply silicon grease (YG6260M) on the contact section of
the heat sink. Before applying new silicon grease,
remove all the old silicon grease. (Old grease may cause
damage to the IC and Transistor).
2. BASIC ADJUSTMENTS
NO.
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
FUNCTION
H POSI MIN
V POSI
V POSI MAX
V POSI MIN
BAKLIGHT CENTER
BAKLIGHT MAX
BAKLIGHT MIN
BRIGHT CENTER
BRIGHT MAX
BRIGHT MIN
TINT CENTER
CONTRAST CENTER
CONTRAST MAX
CONTRAST MIN
CONTRAST 50
COLOR CENTER
COLOR MAX
COLOR MIN
TEXT H POSI
TEXT V POSI
DAC VCOM
Prepare the following measurement tools for electrical
adjustments.
1. Pattern Generator
Fig. 1-2
2-2: WHITE BALANCE
1.
2.
3.
4.
5.
6.
7.
8.
Place the set in Aging Test for more than 15 minutes.
Receive the gray scale pattern from the Pattern
Generator.
Press the button on the remote control to set to the
TUNER mode.
Using the remote control, set the brightness and contrast
to normal position.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (03) on the remote control to
select “R DRIVE (M)”.
Press the UP/DOWN button on the remote control to
select the “R CUTOFF (M)”, “G DRIVE (M)”,
“G CUTOFF (M)”, “B DRIVE (M)”, “B CUTOFF (M)”,
“R DRIVE (H)”, “R CUTOFF (H)”, “G DRIVE (H)”,
“G CUTOFF (H)”, “B DRIVE (H)”, “B CUTOFF (H)”,
“R DRIVE (L)”, “R CUTOFF (L)”, “G DRIVE (L)”,
“G CUTOFF (L)”, “B DRIVE (L)” or “B CUTOFF (L)”.
Adjust the RIGHT/LEFT button on the remote control to
whiten the R CUTOFF (M), G DRIVE (M),
G CUTOFF (M), B DRIVE (M), B CUTOFF (M),
R DRIVE (H), R CUTOFF (H), G DRIVE (H),
G CUTOFF (H), B DRIVE (H), B CUTOFF (H),
R DRIVE (L), R CUTOFF (L), G DRIVE (L),
G CUTOFF (L), B DRIVE (L) and B CUTOFF (L) at each
step tone sections equally.
Perform the above adjustments 6 and 7 until the white
color is looked like a white.
TUNER
01 H POSI OSD
25
2-1: FLICKER
1.
2.
3.
4.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (43) on the remote control to
select “DAC VCOM”.
Check if the screen is flashing.
If screen is flashing, press the " " button on the
remote control and using the LEFT/RIGHT button on
the remote control to adjust the screen.
PAL
4:3
3.
4.
5.
Use the UP/DOWN button or Channel button (0-9) on
the remote control to select the options shown in
Fig. 1-2.
Press the MENU button on the remote control to end the
adjustments.
To display the adjustment screen for TUNER, EXT, PC
and DTV mode, press the button on the remote
control. Press the VOL.DOWN button on the set and the
channel (9) on the remote control for more than 2
seconds.
