Sharp AL-2060 Скачать руководство пользователя

Страница: 76 / 98

SPECIAL FUNCTIONS

SERIAL POLLING

You can poll several fax machines one at a time with a single serial polling operation.
A maximum of 100 fax machines can be polled in one serial polling operation.

Follow these steps to use the serial polling function:

Press the [MENU] key.

Press the [

] key (

) or [

] key (

)

until "9:SERIAL POLL MODE" appears,
and then press the [OK] key.

Dial the number of the fax machine
you want to poll using one of the
following methods:

• Press a Rapid Key or a Group Key.
• Press the [SPEED/SEARCH] key and enter a

two-digit Speed Dial number, and then press
the [OK] key.

• Enter a fax number with the numeric keys.

Press the [OK] key.

Repeat steps 3 and 4
until all numbers have
been entered. After
entering the last number,
go to step 5.

Press the [START] key (

memory

Polling fax

Other fax A
memory

Other fax B
memory

polling

Original is set

sending

Repeated for the

next fax machine

Select serial polling

Fax received

Fax

received

Next fax machine is polled

sending

memory

Polling is approved

Original is scanned

into memory

Original is scanned

into memory

Polling is approved

beep

1,2,3,

SP. FUNC

"9:SERIAL POLL MODE"

Selection

1,2,3,

SP. FUNC

Содержание AL-2060



































































































Результаты поиска

Содержание AL-2060

Отзывы:

Похожие инструкции для AL-2060

Бренды по названию

Популярные бренды

Sharp AL-2060, Руководство по эксплуатации

Результаты поиска

Содержание AL-2060

Отзывы:

Похожие инструкции для AL-2060

Бренды по названию

Популярные бренды