background image

4

SET CURRENT CLOCK TIME

There are two clock modes: 12-hour mode and 
24-hour mode.

Example: 5 o’clock in the afternoon

Clock

Display

12-hour mode

PM   5:00

24-hour mode

17:00

1

 To set to the 12-hour mode, press the 

CLOCK button once.

 

To set to the 24-hour mode, press the 
CLOCK button twice.

2

  Press the TIME ADVANCE or REVERSE 

button to set the current time.

 

•  Keep the button pressed to advance or 

reverse the time display quickly. 

3

  Press the SET/C button.

  •  The colon (:) blinks to indicate that the clock is 

functioning.

NOTE:

• The current time cannot be set when the timer is 

operating.

LOADING BATTERIES

Use two size-AAA (R03) batteries.

1

  Remove the remote control cover. 

2

  Insert batteries, making sure the (+) and 

(-)polarities are correctly a lign ed.

3

  Replace the cover.

4

  Press the RESET Button.

 

• The display indicates “AM 6:00” when 

batteries are properly installed.

NOTE:

• The battery life is approximately one year in 

normal use.

• Replace the batteries when the remote control 

displays " 

 ".

• When you replace the batteries, always change 

both batteries, and make sure they are the same 
type.

• If the remote control does not operate properly 

after replacing the batteries, press the RESET 
button.

• If you will not be using the unit for a long time, 

remove the batteries from the remote control.

HOW TO USE THE REMOTE CONTROL

Point the remote control towards the unit’s signal 
receiver window and press the desired button. The 
unit generates a beep when it receives the signal.
• Make sure  there is no object between the remote 

control and the unit.

•  The signal effective distance is 7m.

CAUTION:

• Do not expose the receiver window to direct 

sunlight. This may adversely affect its operation. 

•  Use of certain fl uorescent lamp in the same room 

may interfere with transmission of the signal. 

• Do not leave the remote control in direct sunlight 

or near a heater. Protect the unit and remote 
control from moisture and shock. 

USING THE REMOTE CONTROL

3
2

1

Cover

AY ZP48LZ_eng_cov.indd 4

09.10.30 2:17:04 PM

Содержание AE-Z48LZ





















Отзывы: