background image

12

PLASMACLUSTER OPERATION

Plasmacluster ions released into the room will 
reduce some airborne mold and viruses.

1

  During operation, press the 

PLASMACLUSTER button.

 

•  The remote control will display “  

  ”.

 

•  The blue PLASMACLUSTER lamp on the  
  unit will light up.

TO CANCEL

Press the PLASMACLUSTER button again.

•  The PLASMACLUSTER lamp on the unit will turn 

off.

NOTE:

• Use of the PLASMACLUSTER operation will be 

memorized, and it will be activated the next time 
you turn on the unit.

• To turn off the PLASMACLUSTER lamp, press 

the DISPLAY button.

• To perform Plasmacluster operation in FAN only 

mode, press the PLASMACLUSTER button when 
the unit is not operating.

  The mode symbol of the remote control will go off 

and the fan speed cannot be set to AUTO.

SELF CLEAN OPERATION

SELF CLEAN operation using Plasmacluster 
ions helps to reduce the growth mold fungus 

 

and dry inside of the unit. It is recommended to 
utilize the operation at seasonal change over.

1

 Press the SELF CLEAN button when 

the unit is not operating.

 

•  The remote control displays “ 

 ”.

 

• The blue PLASMACLUSTER lamp on the unit 

will light up.

 

•  The unit will stop operation after 40 minutes.

TO CANCEL

Press the SELF CLEAN button.

•  The blue PLASMACLUSTER lamp on the unit will 

turn off.

NOTE:

• You cannot set the temperature, fan speed, air 

fl ow direction or timer setting during the SELF 
CLEAN operation.      

• Mold fungus already in existence can not be 

eliminated by this operation.

1

1

AY ZP48LZ_eng_cov.indd 12

09.10.30 2:17:08 PM

Содержание AE-Z48LZ





















Отзывы: