6
TOLL FREE: 1-800-798-7398
7
www.sharkclean.com
ASSEMBLY OF YOUR FLOOR
AND CARPET CLEANER:
NOTE:
The charging adapter
and lower handle will be
shipped inside the packaging.
1
Insert the smaller end of the
lower handle into the top of the
unit. Push until firmly in place.
(
Fig. 1
)
2
Slide the upper pole (the tube
with the handle) into the end
of the Shark
®
Backsaver
™
joint
that has a small notch in it (
a
).
Then slide the lower pole into
the other end of the joint (
b
).
Push it in until it clicks into
place. (
Fig. 2
)
COMPONENTS:
A
Main Unit
B
Speed Control Button
C
Power Button
D
Dust Container
E
Lower Handle
F
Backsaver
™
Release Button
G
Upper Pole with Handle
H
Shark
®
Backsaver
™
Joint
I
Lower Pole
J
Charging Adapter
Fig. 2
Fig. 3
If the brush roll stops moving, it’s probably due
to the anti-jam feature. This feature protects
the motor from becoming overheated. If the
brush becomes overloaded, it will stop turning
and both speed indicator lights will stay on.
Turn off your unit by pressing the power button
once. See page 9 for instructions on removing
or cleaning the brush roll. Wait for 10 seconds
to let your unit cool down. Now press the
power button again and you’re ready to resume
cleaning!
Model Number:
V1945Z 32
Voltage:
7.2 V
F
A
ASSEMBLY
G
H
I
J
3
Insert the Shark
®
Backsaver
™
folding handle you just
assembled into the top of the
lower handle. You should hear
the locking tab click into place.
(
Fig. 3
)
IMPORTANT:
Charge the
batteries for 24 hours before
using the unit for the first time.
See page 7 for instructions on
charging your unit.
Fig. 1
E
B
C
D
1
Always make sure that the unit
is turned off. (
Fig. 4
)
2
Insert the charger plug into
the hole on the back of the
unit. Plug the charger into a
wall outlet. The light next to
the power button will illuminate
when the unit is charging. If the
unit is plugged in and the light is
not illuminated, press the power
button once. The light should
now be illuminated indicating
that the unit is charging.
(
Fig. 5
)
CHARGING YOUR CORDLESS FLOOR AND CARPET CLEANER
3
Charge the battery for 24
hours before initial use and
16 hours for each recharge.
Your cordless floor and carpet
cleaner is powered by Ni-Cd
batteries that need this time to
build up their charge.
4
Always remove the charging
adapter from the unit after the
charging period has completed.
Storing the unit with the
adapter attached and
plugged in will reduce the
battery life
.
IMPORTANT:
Although many
adaptors look similar, it’s
important to use only the
adaptor that came with the unit
(Helms-Man UD3514090020G).
To maintain peak
performance of your unit,
let the battery run down
completely at least once a
month and then recharge it.
indicates the speed optimized to
clean bare floors and two lights
indicate the speed optimized to
clean carpets and larger debris
on bare floors. (
Fig. 7
)
1
Press the power button to start
the unit. The lights on the unit
will illuminate. When finished
cleaning, press the power
button again to turn the unit
off. (
Fig. 6
)
USING YOUR CORDLESS FLOOR AND CARPET CLEANER
2
You can adjust the speed of the
brush roll to suit the floors that
you are cleaning. Press the
button on the right (opposite
the power button) to switch
between speeds. One light
Fig. 6
Fig. 7
FLOOR
CARPET
a
b
Fig. 4
Fig. 5
OFF
V1945Z_32_ENG_IB_100929.indd 6-7
29/09/10 2:32 PM
