background image

8

TOLL FREE:

 1-800-798-7398

CARE AND MAINTENANCE - cont.

For any other servicing, call 

Customer Support at 1-800-798-7398 

or

 visit www.sharkclean.com

3

   Make sure you are working 

in a well-lit area and turn the 
motorized brush over so you can 
see the rotating brush clearly.

4

   Inspect the rotating brush for 

a build-up of debris. Remove 
anything wound around the 
brush by carefully cutting it 
with scissors. The brush roll is 
equipped with a raised cutting 
guide to make inserting scissors 
easier. Avoid damaging or cutting 
the bristles. (

fig. 12

)

5

   Use a flashlight to inspect the 

neck of the motorized brush and 
inside the air duct at the bottom 
of the main body and remove any 
debris or blockages. Reattach the 
motorized brush, ensuring it clicks 
into place.

6

   Remove the dust cup and use the 

flashlight to check the air path 
on the spine of the vacuum and 
remove any debris or blockages. 
Then replace the dust cup.

BRUSH BAR REMOVAL

1

   For easier cleaning, the brush roll 

can be removed from the nozzle. 
Using a coin, turn the dial next to 
the brush roll access door to the 
unlock position. (

fig. 13

) Remove 

the brush roll access door.  
(

fig. 14

)

2

   Slip the black belt off of the white 

gear and lift out the brush roll. 
(

fig. 15

)

BRUSH BAR INSERTION

1

   To reinsert the brush roll, first slip 

the black belt onto the white gear 
(

fig. 16a

), then align the white 

square on the opposite side of 
the brush roll into the square slot. 
(

fig. 16b

2

   Align the white square on the belt 

side and position into its slot.  
(

fig. 17

)

3

   Replace the door, inserting the 

wheel side first. Use a coin to 
move the dial to the lock position.

RESTARTING AFTER A JAM

If the indicator light around the power 
button flashes, the brush bar has 
jammed and will cease to operate.

1

   Turn the unit off and allow it to 

cool down for 10 seconds.

2

   Ensure that nothing is blocking 

the motorized brush or wrapped 
around the brush bar.

3

   Turn the power on and the unit 

should operate normally.

fig. 12

fig. 13

fig. 14

fig. 15

fig. 16a

fig. 16b

fig. 17

 !""##$%&'$""#(#)$*+,-..///7

""0#(0#1///)231/45

Содержание SV1100













Отзывы: