4
5
www.sharkclean.eu
0800 862 0453
fig. 9
fig. 6
fig. 8
fig. 7
IMPORTANT:
Always check with the carpet
manufacturer or distributer before using the
Shark
®
Activating Pretreater Stain & Odour
Remover or the Low Moisture -No Rinse - Carpet
Cleaner. To determine the colour fastness of any
carpet -especially with reds or blues - take a
clean, moist towel and gently rub a small area in
an inconspicuous area. If colour comes off on the
towel, you should discontinue use.
Using Your Sonic Duo
™
Carpet, Wood & Hard Floor Cleaner
fig. 10
fig. 11
Cleaning Your Carpets
The
Sonic Duo
™
comes with a Reusable Bottle with
a “Purple” cap and label. This bottle is to be used
with the Low Moisture –No Rinse- Carpet Cleaner.
The
Sonic Duo
™
also has a second Carpet Mode (II)
that should be used when cleaning carpets. Please
note that not all carpets react to the Sonic Duo the
same way. Some carpets will require more time and
cleaning solution than others.
REGULAR CLEANING
Step 1:
1
Vacuum your carpets and/or area rugs to remove
any loose dirt, dust, or debris that may have
accumulated in the carpet.
Step 2:
2
Attach the Carpet/Rug Cleaning Pad to the
bottom of the
Sonic Duo
™
. This pad has a
“Purple” trim and tag that says Carpet/Rug
Cleaning Pad. Attach the pad as shown in
(
Fig. 6
) – the tag should be positioned toward
the back of the
Sonic Duo
™
.
3
Remove the Reusable Bottle by holding it and
pulling up (
Fig. 7
). Remove the cap by turning it
counterclockwise.
7
Lightly step on the back of the scrubbing head to
release the handle.
WARNING
: Never stand on the
Sonic Duo
™
.
8
Begin cleaning by pressing the Spray Button to
apply the cleaning solution to the carpet that
is to be cleaned. (
Fig. 12
) Spray the solution
continuously while pushing the unit forward
and then pulling it backward until the area to be
cleaned is damp.
NOTE
: The first time that you use the
Sonic
Duo
™
there may be air in the system causing a
delay for the solution to come out of the spray
nozzle. Hold the spray button down for 5 to 10
seconds until you see the solution spray out.
9
Using the same back and forth motion, continue
to go over the area a few times without spray.
Work your way through the room or area being
cleaned methodically. Repeat as necessary until
the entire carpeted area has been cleaned. No
rinsing is required.
10
If the Reusable Bottle is empty, you can refill
it at any time as long as the
Sonic Duo
™
is
unplugged from the outlet.
11
Once finished, step on the tag of the Carpet/
Rug Cleaning Pad and lift the unit to remove the
Carpet/Rug Cleaning Pad from the
Sonic Duo
™
(
Fig. 13
). Let the carpet dry thoroughly and then
vacuum.
4
Fill the Reusable Bottle with the “Purple” trim
and label with water until the “1:7 Water” fill
line and then with the Low Moisture –No Rinse-
Carpet Cleaner until the “Solution” fill line.
(
Fig. 8
)
Always fill with water first and then add the
cleaning solution so to avoid foaming and
ensure accuracy when measuring.
5
Screw the bottle cap on tightly and insert the
Reusable Bottle into the unit. Push it down to
make sure that it is well inserted. You will hear
an audible “Click” when the Reusable Bottle is
inserted properly. (
Fig. 9
)
6
Twist the quick cord release holder to unwrap
the power cord completely. (
Fig. 10
) Plug into
an electrical outlet and slide the “ON/OFF”
button to turn the
Sonic Duo
™
on. Select the
faster Carpet Mode (II). (
Fig. 11
)
HIGH TRAFFIC AREA CLEANING
Step 1:
1
Vacuum your carpets and/or area rugs to remove
any loose dirt, dust, or debris that may have
accumulated in your carpet.
2
Pretreat high traffic area by spraying Activating
Pretreater Carpet Stain & Odour Remover. Spray
the area until saturated and let sit for 5-10minutes.
Step 2:
3
Attach the
Carpet Scrub‘n Stain
™
Pad
to
the bottom of the
Sonic Duo
™
. This pad has a
“Purple” Trim and tag that says
Carpet Scrub
‘n Stain
™
Pad
. Attach the pad as shown in
(
Fig. 14
) – the tag should be positioned toward
the back of the
Sonic Duo
™
.
4
Remove the Reusable Bottle by holding it and
pulling up. (
Fig. 15
) Remove the cap by turning
it counterclockwise.
5
Fill the Reusable Bottle with the “Purple” Trim
and label with water until the “1:3 Water” fill
line and then with the Low Moisture –No Rinse-
Carpet Cleaner until the “Solution” fill line.
(
Fig. 16
)
Always fill with water first and then add the
cleaning solution so to avoid foaming and
ensure accuracy when measuring.
fig. 14
fig. 16
fig. 15
fig. 12
fig. 13
