background image

OPERATING INSTRUCTIONS cont.

OPERATING INSTRUCTIONS cont.

WINDING & UNWINDING THE 

POWER CORD

This vacuum cleaner is 

equipped with a convenient 

cord storage feature. The 

power cord winds around 

the two cord holders at 

the back of the unit.  The 

bottom one has a quick 

cord release feature. 

Turn the cord hook to 

the left or the right to 

remove the power cord.

See illustration at right.

ON/OFF SWITCH 

• The On/Off switch has two different 

positions.

• Push on the "I" side to turn the 

vacuum ON.

• Push on the "O" side to turn the 

vacuum OFF.

USING THE UNIT AS A HAND 
VACUUM

• Press the telescopic tube release 

button to remove the telescopic tube. 

(See page 4)

• Press the floor brush release button to 

remove the floor brush. (See page 4)

• Attach the shoulder strap to the 

shoulder strap attachment point. (See 

illustration below.)

• Attach the crevice tool or the dusting 

brush to the end of the hose.

Crevice Tool

For radiators, crevices, corners, 

baseboards and 

between cushions.

Dusting Brush

The dusting brush is 
used for the furniture, 
venetian blinds,
books, lamp shades 
and shelves.

USING THE UNIT AS AN UPRIGHT

• Unwind the power cord 

and plug into the 

120V outlet.

• Push down on the 

locking button to adjust 

the height of the 

telescopic handle.

NOTE:

When vacuuming 

deep pile carpets or 

hard to vacuum 

carpets, lower the angle 

of the telescopic 

handle (see 

illustration at 

right) for 

easier 

maneuverability.  

Low

er

WARNING

After extended use, the body of the 

vacuum cleaner may become hot. 

When using the unit with the shoulder 

strap, the unit will touch the body of 

the user. Therefore, make sure that 

the unit body is cool before you use 

with the shoulder strap. If during use, 

the vacuum gets too warm, allow it to 

cool before continuing to use.

5

= OFF

= ON

When the Intelli-Sense

TM

Filter 

Monitor lights up, it means that the 
dust cup is full or the HEPA filter or 
Debris Screen needs cleaning.  
You must empty the dust from the 
dust cup and clean the HEPA filter 
and Debris Screen right away. 

Intelli-Sense

TM

Filter Monitor

Turbine

Tilt
Upwards

Locking Latch

From time to time, the turbine of your 
turbo brush will require cleaning. To do 
this:
1. Remove the turbo brush from the hose 

or telescopic extension tube.

2. Slide locking latch forward then tilt the 

top housing of the brush upwards. The 
top housing is hinged and will tilt up 
approximately 45° only. 

3. There may be some dust, lint, hair, etc 

on the turbine wheel. Remove as much 
of this as possible.

4. You may also use the unit’s hose with 

crevice tool attached and use the 
vacuum to remove any additional 
debris from the turbine.

5. Ensure that the turbine wheel moves 

freely by rotating it with your finger. If 
the turbine does not rotate, call 
Customer Service for help.

6. Once clean, close the top cover of the 

turbo brush and slide the locking latch 
toward the rear of the brush to lock.

To use the air driven turbo brush to 

clean upholstery:

1. Remove the flexible hose from the 

hose connector. (See below)

2. Push the air driven turbo brush onto 

the end of the flexible hose as far as 

it will go. 

Cleaning Air Driven Turbo Brush

6

Attaching the Air Driven Turbo 
Brush to the Flexible Hose

Using The Unit With Air Driven 
Turbo Brush

Air Driven Turbo Brush

Important:

In order to ensure that 

maximum air suction is maintained, 

empty the dust cup frequently and shake 

out the HEPA filter and Debris Screen at 

the same time. Ensure that the rotating 

brush is kept free of hair and string which 

may accumulate and decrease brush 

performance.

The efficiency of your air driven turbo 

brush depends on the bristle brush 

rotating at high speed. Strong air suction 

is needed to accomplish this. In order to 

ensure that maximum air suction is 

maintained, please read the following 

instructions:
1. Empty the dust cup frequently.

2. Always shake out the HEPA filter and 

Debris Screen when emptying the dust 

cup container.

3. Ensure that the rotating brush is kept 

free of hair and string which may 

accumulate and decrease brush 

performance.

4. Keep Air Driven Turbo Brush turbine 

free of dirt and foreign matter. (See 

illustration for cleaning instructions.)

Отзывы: