manualshive.com logo in svg

Shark 1.103-841.0, Руководство по обслуживанию

Поделиться
Скачать
Shark 1.103-841.0 Скачать руководство пользователя страница 27

27

Maintenance

Torque Wrench Method

Make sure nut is loose. Tighten nut with torque wrench 
to an initial torque of 50 ft. lbs. Loosen nut from initial 
torque and fingertighten. Insert new cotter pin through 
nut and spindle. If equipped with Posi-Lube, reset tang. 
If necessary loosen, never tighten, nut to align slot with 
the hole in the spindle. Bend one leg of cotter pin over 
the end of the spindle and the other leg over the nut. 
Tap legs slightly to set. Cotter pin must be tight.

Posi-lube Lubrication Procedure

1.

Remove the rubber cap at end of the grease cap.

2.

Using a standard grease gun place the tip onto the 
grease fitting at the end of the spindle.

3.

Pump the grease into the fitting as you continue 
pressure you will notice the old grease coming out 
at the cap. When you begin to see the new grease, 
remove the gun and clean off any excess and 
replace the rubber cap.

Shark SMT Operator’s Manual  9.800-504.0 - E

Содержание 1.103-841.0

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды