manualshive.com logo in svg

Shark 1.103-841.0, Руководство по обслуживанию

Поделиться
Скачать
Shark 1.103-841.0 Скачать руководство пользователя страница 17

17

Operations

Assembly Instructions

STEP 1:

 Attach a 5/8" garden hose to 

inlet connector. Minimum flow should 
be 5 gpm.

STEP 4:

 Check oil level on sight 

glass on backside of pump. Oil 
should be visible one-half way up 
sight glass (10-40W non-detergent). 
The oil level can also be checked by 
using the dipstick on the top of the 
pump.

STEP 2:

 Attach high pressure hose 

to discharge nipple using quick 
coupler. Lock coupler securely into 
place by pulling back coupler collar 
and inserting it onto discharge nipple, 
then pushing collar forward to lock in 
place.

NOTE: If using detergent injector, 
attach detergent injector to 
discharge nipple using quick 
coupler. Attach high pressure hose 
to other end of detergent injector.

STEP 5:

 Fill gasoline tank and check 

engine oil.

Fill diesel tank with diesel fuel.

CAUTION: Do not confuse diesel 
fuel and gasoline when filling 
tanks. Keep proper fuel in proper 
tanks.
ATTENTION: Ne pas confondre du 
carburant diesel et l'essence au 
moment de remplir les réservoirs.

NOTE: Diesel Fuel Shut-off must 
be in the ON position prior to 
turning on burner.

STEP 3:

 Attach wand to spray gun 

using teflon tape on threads to 
prevent leakage. Attach swivel 
connector on discharge hose to 
spray gun using teflon tape on 
threads. Attach swivel connector on 
high pressure hose to spray gun 
using teflon tape on threads. Engage 
safety latch to prevent from triggering 
gun.

STEP 6:

 On electric start models, 

you will need to install a battery 
making sure that the red cable is 
attached to the positive terminal. Use  
a Group U1 garden tractor style type 
of battery rated for 300 CCA (battery 
not included).

NOTE: Battery is required for 
burner to operate.

CAUTION: These machines are 
intended to be protected from 
outside environments.

ATTENTION: Ces machines sont 
conçues pour être protégées 
contre l'environnement extérieur.

CAUTION: Risk of injury. Discon-
nect battery ground terminal 
before servicing.

ATTENTION: Risque de blessures. 
Débrancher la borne de mise à la 
terre de la batterie avant de 
procéder à des opérations d'entre-
tien.

Shark SMT Operator’s Manual  9.800-504.0 - E

Inlet 

Connector

High Pressure

Hose

Discharge

Nipple

Detergent 
Hose

Detergent 

Injector

(Option)

Safety 

Latch

Dipstick

Gasoline

Tank

POS

NEG

Red

Black

Diesel Fuel

Tank

Содержание 1.103-841.0

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды