22
Control Microcomputer
Giotto Spot 400 CMY rel.1.00
3.17 Locking/unlocking the shutter
This feature allows to disable or enable Shutter closure if PAN or TILT lose their position.
1.
Connect Giotto Spot to the power supply, wait until it has finished reset procedure and "DMX signal" appears
on the display.
2.
Use the UP/DOWN keys to go to the "CSHUTT" menu
3.
Press "Enter" and hold it down for a few seconds to confirm. The message on the display starts flashing.
4.
Use the UP/DOWN keys to select "CSHUTT=EN " or "CSHUTT=DN " to enable or disable the closure of the
shutter if the fixture is accidentally moved.
5.
Press "Enter" to save the value set
3.18 Setting default parameters
This feature allow to set the default parameters:
1.
Connect Giotto Spot to the power supply, wait until it has finished reset pro-
cedure and "DMX signal" appears on the display.
2.
Use the UP/DOWN keys to go to the "FACT" menu.
3.
Press "Enter" to confirm. The message on the display starts flashing.
4.
Use the UP/DOWN keys to select "FACT=SET" and press "Enter".
5.
By pressing "Enter" in this mode, the default parameters shown in the table
are set and "FACT=OFF" appears on the display.
3.19 Restoring default parameters
This feature allows to reset the values of the parameters which were set immediately before FACT=SET procedure.
In other words, if the default parameters have been set by mistake, this allows to return to the values previously set.
1.
Connect Giotto Spot to the power supply, wait until it has finished reset procedure and "DMX signal" appears
on the display.
2.
Use the UP/DOWN keys to go to the "Prev" menu
3.
Press "Enter" and hold it down for a few seconds to confirm. The message on the display starts flashing.
4.
Use the UP/DOWN keys to select "PREV=SET"
5.
Press "Enter" - this restores the values, cancelling the FACTORY DEFAULT operation. In the meantime,
PREV stops flashing and PREV=OFF appears.
3.20
Setting the starting position of the rotating gobos and the gobo, colour and effects wheels
From the Setting menu, it's possible to set the starting position of the colour, gobo and effects wheels, as well as
the starting position of the rotating gobos. To carry out the setting, proceed as follows:
1.
Connect Giotto Spot to the power supply, wait until it has finished reset procedure.
2.
Use the UP/DOWN keys to go to the "SETTING" menu
3.
Press "Enter" .
4.
Use the UP/DOWN keys to select "COL, GOB1, GOB2, RGOB1, RGOB2
5.
Press "Enter" to select - the writing on the display will begin to flash.
6.
Set the offset with the UP/DOWN keys
7.
Press ENTER to confirm (the writing stops flashing) and return to the SETTING submenu
8
Once all the settings have been done, press ENTER for 4 seconds to exit the Setting menu.
Menu
Item
Default
Parameter
ADDR
001
Pmove
NORM
PP_min
000 gradi
PP_max
540 gradi
Tmove
NORM
TP_min
000 gradi
TP_max
240 gradi
SWAP
OFF
SIGN
DMX
SMD
16 BIT
GMD
8 BIT
LMP_ctr
DS
RST_ctr
EN
SPEED
100%
ACCEL
FAST
Bright
40%
DMXdly
UNL
CSHUTT
DS
RGOB2=0
RGOB1=0
GOB2=0
GOB1=0
COL=0
SETTING
PREV=OFF
PREV=Set
FACT=Off
FACT=Set
CSHUTT=DN
CSHUTT=EN
