background image

16

Product Version 1.0 | Revision E | Released 2023-01-11

PLEASE NOTE! POI FIXTURES SHOULD BE PRE-SET WITH ANY CUSTOM PROGRAMMING 

BEFORE INSTALLATION

ALTHOUGH MOST FUNCTIONS ARE POSSIBLE TO BE SET VIA RDM ONCE MOUNTED IN POSITION, IT IS EASIER 
TO DO CONFIGURATION AND ANY TROUBLESHOOTING BEFORE MOUNTING IS COMPLETE.

UNPACKING

Unpack the device and inspect it to ensure that it has not been damaged during transport.
The G-7 Spot is shipped with:

•  Two POI omega brackets suited for M-10 holes.

•  Safety information leaflet.

APPLICATION CONSIDERATIONS

The fixture is IP66-rated and designed for both indoor and outdoor events. This means that it is protected from:

•  Dust, to the degree that dust cannot enter the device in sufficient quantities, as to interfere with its opera-

tion.

•  High pressure water jets from any direction.

When selecting a location for the device, ensure that:

•  It is situated away from public thoroughfares and protected from contact with people.
•  It is not immersed in water.
•  It has adequate ventilation.

When using the fixture with a DMX controller, ensure that:

•  According to RS485 standard, the DMX Out of the last fixture should be terminated with a 120 ohm resistor 

between pin 2 and 3.

•  If the resistor is not installed, make sure that the DMX Out is properly sealed by mounting the protection cap, 

in accordance with the ingress protection (IP) requirements.

•  A maximum of 32 fixtures can be connected to the same DMX link.

CONNECTING TEMPORARY POWER

Connect to AC power using the supplied 8mm cable (the larger of the two permanently wired cables). The fixture 
must be grounded/earthed. The AC power supply must incorporate a fuse or circuit breaker for fault protection. For 
temporary programming, a plug or terminals can be used.The power cable color coding is shownin fig. 9:

• 

Connect the black wire to live

• 

Connect the white wire to neutral 

• 

Connect the green/yellow wire to ground (earth)

The fixture must be grounded/

earthed and be able to be isolated 

from AC power. The AC power 

supply must incorporate a fuse or 

curcuit breaker for fault protection.

Color

Black

White

green/yellow

Conductor

live

neutral

ground (earth)

Symbol

or

L

N

Wire

Figure 9 : Connecting AC Power

CONFIGURATION

The G-7 Spot POI does not include a display, and is configured through RDM (Remote Device Management). See 
"RDM" on page 29 for more information.
In G-7 Spot POI, the DMX address and DMX mode can only be set through RDM. When addressing through USB 
powered DMX/ RDM devices, ensure DMX link is terminated, and keep the cable as short as possible.
DMX modes for POI are the same as the G-7 Spot standard. Visit www.sgmlight.com to see all DMX charts available 
under the respective product, or upon request via [email protected].

PLEASE NOTE! REMOTE DEVICE MANAGEMENT (RDM) REQUIRES A CORRECT DMX CABLED INSTALLATION AND 
TERMINATION. WHEN SETTING ADDRESSES THROUGH RDM AND USING USB DONGLES, DISABLE USB SELEC-
TIVE SUSPEND TO ENSURE A PROPER VOLTAGE TO THE DMX LINK. IF ANY LAG OR TROUBLE OCCURS WHEN 
ADDRESSING, DECREASE THE CABLE LENGTH RANGE TO <12 M. AND ONLY ADDRESS ONE FIXTURE AT A TIME.

Содержание G-7 SPOT













































Отзывы: