manualshive.com logo in svg

SG Models SEA276, Инструкция по сборке

Поделиться
Скачать
SG Models SEA276 Скачать руководство пользователя страница 2

P-51D MUSTANG

Instruction Manual.

2

 

Thank you for choosing the 

P-51D MUSTANG 

ARF by 

SG MODELS

. The 

P-51D MUSTANG 

was designed with the intermediate/advanced sport flyer in mind. It is a semi scale airplane 

which is easy to fly and quick to assemble. The airframe is conventionally built using balsa, 

plywood to make it stronger than the average ARF, yet the design allows the aeroplane to be 

kept light. You will find that most of the work has been done for you already. The motor mount 

has been fitted and the hinges are pre-installed. Flying the 

P-51D MUSTANG

 is simply a joy.

This instruction manual is designed to help you build a great flying aeroplane. Please read this 

manual throughly before starting assembly of your 

P-51D MUSTANG

 . Use the parts listing 

below to indentify all parts.

 

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is 

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU 

ASSUME ALL RISK & REPONSIBILITY.

If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C 

supplier and join your local R/C model Flying Club. R/C Model Flying Clubs offer a variety of 

training procedures designed to help the new pilot on his way to successful R/C flight. They 

will also be able to advise on any insurance and safety regulations that may apply.

INTRODUCTION.

WARNING.

KIT CONTENTS

1

5

2

3

3

2

4

6

7

Содержание SEA276





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды