SFC Energy XTREMESOLAR XTR-F300P Скачать руководство пользователя страница 3

Страница: 3 / 22

1. Aluminum Frame

2. Tempering glass

3. Encapsulating EVA

4. Cell

5. Back sheet

6. Silicone adhesive

7. Junction box

8. Nameplate

9. Cable

10. Connector

11. Mounting hole

12. Grounding hole

13. Drainage hole

14. Cell

3.1 Product Identification

Each module has two labels providing the following information:

1. Nameplate: describes the product type; Peak power, Max. power current, Max. power voltage, open

circuit voltage, short circuit current, all as measured under standard test conditions; Certification marks, the

maximum system voltage etc.

2. Barcode: each individual Module has a unique serial number. The serial number has 16 digits. It is

permanently attached to the interior of the Modules and is visible from the top front of the Module. This

barcode is inserted prior to laminating. In addition, you can find a same barcode beside the nameplate.

3.2 Conventional Safety

Xtremesolar Modules are designed to meet the requirements of IEC 61215 and IEC 61730, application class A.

Modules rated for use in this application class may be used in system operating at greater than 50V DC or

240W, where general contact access is anticipated. Modules qualified for safety through IEC 61730-1 and IEC

61730-2 and within this application class are considered to meet the requirements for safety class II

equipments.

When Modules are mounted on rooftops, the roof must have a fire resistant covering suitable for this

application. Rooftop PV systems should only be installed on rooftop that is capable of handling the

additional weighted load of PV system components, including Modules, by a certified building specialist or

engineer and have a formal structure of the complete analysis result.

For your safety, do not attempt to work on a rooftop until safety precautions have been identified and taken

including without limitation fall protection measures, ladders or stairways, and personal protective

equipment.

For your safety, do not install or handle Modules under adverse conditions, including without limitation

strong or gusty winds, and wet or frosted roof surfaces.

Содержание XTREMESOLAR XTR-F300P























Результаты поиска

Содержание XTREMESOLAR XTR-F300P

Отзывы:

Похожие инструкции для XTREMESOLAR XTR-F300P

Бренды по названию

Популярные бренды

SFC Energy XTREMESOLAR XTR-F300P, Руководство по установке

Результаты поиска

Содержание XTREMESOLAR XTR-F300P

Отзывы:

Похожие инструкции для XTREMESOLAR XTR-F300P

Бренды по названию

Популярные бренды