Seymour AV Center Stage XD Скачать руководство пользователя страница 16

Страница: 16 / 19

www.seymourav.com



Bump up/down.

Long presses will travel the motor longer, and little quick

presses will bump the motor. Hit your lower limits target, while making sure the
cables are ok per the above mention.



Press Stop.

This will exit lower limits mode you just programmed. The beeping

will change for a couple beeps to confirm and the motor will do a little bump.

Gen3 Limits Setting Flowchart

Graphically, here is how the standard RF motor’s limits adjustment algorithm works. Again, I
recommend prior to entering this mode to raise the screen all the way up first, since it’s very unlikely
you want to adjust the upper limits:

Hold <stop> and

<down> for a few

seconds. The motor

starts beeping

repeatedly.

Is the motor

in the

intended

upper limits?

Press <down> and

then <stop> to exit

continuous mode

and enter bump

mode.

Press <up> or

<down> to adjust

motor to the precise

upper limits.

Press <stop> to exit

upper limits mode.

YES

Now the motor is in lower limits

setting mode. Press <down> and

wait until motor is a few inches

away from the targeted lower limit.

Press <stop> to exit

continuous mode and

enter bump mode.

Press <up> or <down> to adjust

motor to the precise lower limits.
Check that you aren’t exceeding

the cables’ capabilities.

Press <stop> to exit lower

limits mode. The motor will

beep in confirmation and do

a little jog. The incessant

beeping sounds cease.

Содержание Center Stage XD




















Результаты поиска

Содержание Center Stage XD

Отзывы:

Бренды по названию

Популярные бренды

Seymour AV Center Stage XD, Инструкция по эксплуатации

Результаты поиска

Содержание Center Stage XD

Отзывы:

Бренды по названию

Популярные бренды