SEVERIN KS 9893, Инструкция по эксплуатации

Страница: 12 / 84

12
room.
∙ It should be operated in conditions where the relative
humidity is no more than 70 %.
∙ The product data sheet contains details of the ambient
temperature range suitable for this appliance.
∙ Do not use the appliance outdoors. Ensure that the plug is
accessible and can be removed from the wall socket at any
time.
∙ Do not expose the appliance to direct sunlight, and do not
position it next to any heat sources (radiators, cookers etc.).
If this cannot be avoided, however, suitable insulation must be
in installed between the heat source and the unit.
∙ The unit must not be installed inside a cupboard; when
positioning the unit, also ensure that it is not placed directly
underneath a shelf or any other similar object.
∙ Ensure that there is suf fi cient space in front for the door to
open to 160°.
∙ In the case of uneven fl oors, the adjustable feet at the front
can be used to compensate and ensure optimum stability.
Ventilation
Ensure that there is enough space around the unit so that the
air circulation round and behind it is not obstructed. (Rear and
sides 5 cm, top 10 cm.)
Reversible door
The design provides for the door to be reversed, i.e. for right-
hinged (default installation) to become left-hinged.
Warning: Always disconnect the unit from the mains before
any maintenance or repair work is carried out.
1. Remove the four screw covers (11) and the screws (10).
2. Remove the top panel (9), and the cover plate (8) from the
front.
3. Remove the two screws (6) securing the upper hinge plate
(5) on the right-hand side.
4. Carefully lift up the door and place it on a suitable surface
to protect it from scratches.
5. Take off the white plug (7) and re-position it in the
corresponding hole on the right-hand side, pushing it fi rmly
down.
6. Remove the two screws (1) securing the lower hinge plate
(2) on the right-hand side.
7. Take out the adjustable foot (4) and re-position it on the
right-hand side.
8. Mount the lower hinge plate (2) using both screws (1) in
its new position on the left. Ensure that the plate is aligned
parallel to the side edge of the unit. (Do not fully tighten
the screws yet.)
9. Replace the door in its new position. Ensure that the
hinge pin of the lower hinge plate is inserted into the guide
bushing (hole) in the door.
10. Mount the upper hinge plate (5) using both screws (6) in
its new position on the left. Ensure that the hinge pin is
inserted into the guide bushing (hole) in the door. (Do not
fully tighten the screws yet.)
11. Close the door and ensure that it is properly aligned
before fully tightening the screws of the upper and lower
hinge plates.
12. Fit the top panel (9) on the unit and – with the door open
– replace the cover plate (8) into the opening on the right-
hand side of the front.
13. Replace the screws (10) and screw covers (11) on the top
panel (9).
14. Put the unit back in its intended position and wait for about
two hours before connecting it to the mains.
Temperature control
The unit is activated by
connecting it to the mains. It
is only switched off completely
when the plug is removed from
the wall socket.
The temperature in the refrigerator cabinet can be adjusted by
setting the temperature control. Turning the control clockwise
will decrease the temperature, while turning it anti-clockwise
will increase it.
∙ After switching on, the temperature control should be set to
its highest setting.
∙ After approx. 30 minutes, the temperature should be
changed to a medium setting, which is usually suf fi cient for
home or of fi ce use. Following a power interruption, or if the
unit has been switched off on purpose, it may take 3 to 5
minutes before it switches on again.
Note: In position ‘0’, the cooling function is switched off,
though the appliance is still connected to the mains.
Interior lighting
Changing the light bulb:
∙ Remove the plug from the wall socket.
∙ Use a suitable screw-driver to remove the screw holding the
light cover and take the cover off.
∙ Take out the defective bulb and fi t a new one (max. 15 W.,
socket type E14).
∙ Put the cover back into position, replace the screw and
tighten it.