INTRODUCTION
Congratulations! on being a proud owner of a
Steal Shield
.
This Immobiliser system will give you piece of mind against
burglars and intruders.
This Product has been approved by the AU/NZS4601:1999
Immobiliser Standards. To obtain the best results from your
security system, we suggest you read the instruction manual
carefully.
STEAL SHIELD “a shield you can trust”
EMERGENCY DISARM
Digital Pin Code Override System!
The system can be disarmed by entering 5 digits of the over-
ride no. Each digit is entered individually using the ignition
switch. Following example shows how the override number
45258 would be used. “Digital pin should have been given by
the installer”
1. Turn the ignition on while the system is armed, the LED will
stay on.
2. Turn the ignition OFF, the LED will start flashing. Count the
number of flashes. After the 4
th
flash, turn the ignition on. The
LED will stay on.
3. Turn the ignition off, and count the number of flashes. After
the 5
th
flash, turn the ignition on. The LED will stay on.
4. Turn the ignition off, and count the number of flashes. After
the 2
nd
flash, turn the ignition on. The LED will stay on.
5. Turn the ignition off, and count the number of flashes. After
the 5
th
flash, turn the ignition on. The LED will stay on.
6. Turn the ignition off, and count the number of flashes. After
the 8
th
flash, turn the ignition on. The siren will chirp once and
the system will disarm.
Note
If the digit is a “0”, wait 10 flashes before turning ignition “on”
Should you miss the LED flashes or enter a digit incorrectly,
wait for 11 flashes and simply repeat the procedure from step
one then re-enter from the first digit of the override code.
SYSTEM FEATURES
Rolling Code Remote’s
Each time the remote is used, the code changes. The system brain will
only respond to a certain code once, so any attempt to "record and play
back" a remote transmission with a code copier , will not be accepted by
the system brain.
Auto Engine Immobilliser
35 seconds after you turn the ignition off, system immobilise the vehicle.
Security Re-Arm
System will re-arm if it is disarmed & a door is not opened within 35 sec-
onds.
Indicator Flash
Gives a visual indication of the system arm, disarm & trigger.
Theft Deterrent LED
This is normally installed in the dash board, to describe the visual status of
the system to warn the intruders.
Immobiliser
When ever the system is armed, it disables the car engine from being
started, making it harder to steal. If the battery is disconnected and re-
reconnected, the system will return to the original state.
Personal Protection Alarm
Works as a personal alarm to grab attention.
Digital LED Reporting
The LED will give a digital diagnostic code to tell you the status;
2 F/S System Armed & 10 F/S Auto Arming, and Security Re-Arm.
Error Sector Isolation
If any sector triggers for 3 times or more when armed, it will automatically
isolate it, till the next arm.
IMPORTANT NOTICE
The digital pin card supplied by the Installer must be kept in a secure place
as this contains your unique pin number to disable the system in an emer-
gency.
SYSTEM OPERATION
Arming the System
1.
Press & release the transmitter button #1.
2.
Two chirp & Indicators flash verifies system is on.
3.
Doors will lock ( Central Locking must be installed).
4.
LED will flash slowly.
Disarming the System
1.
Press and release the transmitter button #1.
2.
One chirp & Indicators will stay on for 10 Sec. System is off
doors will unlock (Central locking must be installed).
Personal Protection Alarm (Panic)
1.
Press and hold the transmitter button #1 for 3 sec.
2.
Siren will sound & Indicators will flash for 3 min’s.
3.
To cancel Panic press button #1.
Trunk Release Option
Press and hold the transmitter button #2 for 3 sec. Two chirps & Indi-
cators flash indicates operation of trunk release (if installed).
One Time Soft Chirp
(Arm/Disarm chirp can be temporarily disabled from your remote)
1.
Press & release transmitter button #2
2. Press & release transmitter button for desired function
.
Precautions
•
We suggest you test the system weekly to maximize protection for your car
•
If you jump start your car, always use a surge protected jump lead to prevent any damage to the
alarm system
•
If a mobile phone is left in the car with the power on, it can give false alarms due to the radio
waves emitted from the phone
Button #2
Button #1
