background image

D150-01-00

1

I56-599-03R

B116LP Plug-in Detector Base

For use with the following smoke detectors:
In US:

1151, 2151

In Canada:

1151A, 2151A

In Europe:

1151E, 2151E

INSTALLATION AND MAINTENANCE INSTRUCTIONS

3825 Ohio Avenue,

St. Charles, Illinois 60174

1-800-SENSOR2, FAX: 630-377-6495

Before Installing

Please thoroughly read the System Sensor manual I56-407,

Guide for Proper Use of System Smoke Detectors

, which pro-

vides detailed information on detector spacing, placement,
zoning, wiring, and special applications. Copies of this
manual are available at no charge from System Sensor. (For
installation in Canada, please refer to CAN4-S524, Standard
for the Installation of Fire Alarm Systems and CEC Part 1,
Sec. 32.) 

NOTICE:

This manual should be left with the owner/user

of this equipment.

IMPORTANT:

The detector used with this base must be

Specifications

Base Diameter:

6.2 inches (157 mm)

Base Height:

0.95 inches (24 mm)

Weight:

0.3 lb. (130 g)

Mounting:

4-inch square box with or without plaster ring. Min. Depth–1.5 inches
4-inch octagon box. Min. Depth–1.5 inches
3-1/2 inch-octagon box. Min. Depth–1.5 inches
50 mm box
60 mm box
70 mm box

Operating Temperature Range:

0° to +49°C (32° to 120°F) US and Canadian Installations
10° to 60°C (14° to 140°F) European Installations

Operating Humidity Range:

10% to 93% Relative Humidity

Electrical Ratings – includes base and detector

System Voltage:

24 VDC

Maximum Ripple Voltage:

4 Volts peak to peak

Start-up Capacitance:

0.02

µ

F Maximum

Standby Ratings:

15 VDC Minimum
35 VDC Maximum
120 

µ

A Maximum

Alarm Ratings:

8 V Minimum at 16 mA
12 V Maximum at 100 mA
(Alarm current MUST be limited to 100 mA maximum by the control panel.)

Relay Contact Ratings:
Resistive or Inductive (60% power factor) Load
Form C:*

2.0A @ 30 VAC/DC
0.6A @ 110 VDC
1.0A @ 125 VAC

Reset Voltage:

1.4 VDC Minimum

Reset Time:

0.3 Seconds Maximum

Start-up Time:

34.0 Seconds Maximum

*For Canadian installations relay contact ratings are 2.0A @ 30 VAC/DC.

tested and maintained regularly following NFPA 72 require-
ments. The detector used with this base should be cleaned
at least once a year.

General Description

The model B116LP plug-in detector base is used with
System Sensor model 1151, 1151A,  and 1151E ionization
detector heads and model 2151, 2151A, and 2151E photo-
electronic detector heads. The capability of plugging these
detectors into a variety of special bases makes them more
versatile than equivalent direct-wired models. Refer to the
System Sensor catalog for other available plug-in detector
bases.

Содержание B116LP

Страница 1: ...ure Range 0 to 49 C 32 to 120 F US and Canadian Installations 10 to 60 C 14 to 140 F European Installations Operating Humidity Range 10 to 93 Relative Humidity Electrical Ratings includes base and detector System Voltage 24 VDC Maximum Ripple Voltage 4 Volts peak to peak Start up Capacitance 0 02µF Maximum Standby Ratings 15 VDC Minimum 35 VDC Maximum 120 µA Maximum Alarm Ratings 8 V Minimum at 16...

Страница 2: ...l panel manufacturer s specifications for the total loop resistance allowed for the particular model control panel being used before wiring the detector loops Locate installations where normal ambient temperatures do not exceed 100 F Wiring Instructions For system supervision For terminals 2 3 and 5 do not use looped wire under terminals Break wire run to provide system supervision of connections ...

Страница 3: ...ring diagram POWER LOOP 2 WIRE CONTROL PANEL POWER LOOP 3 2 4 5 1 12 13 14 COM CONTACT N C AUXILIARY N O FORM C E O L CLASS A OPTIONAL WIRING A78 1577 00 remove the detector from the base once the tamper resist ance feature has been activated place a small bladed screwdriver into the small hole on the side of the base and push plastic lever away from the detector head see Figure 3B This will allow...

Страница 4: ... 800 SENSOR2 736 7672 for a Return Authorization number send defective units postage prepaid to System Sensor Repair Department RA __________ 3825 Ohio Avenue St Charles IL 60174 Please include a note describing the malfunction and suspected cause of failure The Company shall not be obligated to repair or replace units which are found to be defective because of damage unreasonable use modification...

Отзывы: