background image

MOD-10-1164

 

sepura 

 

TETRA Terminals 

Product Guide 

14-09-2012 

Page 30 of 46 

Issue 11 

© Sepura plc 2012 

 

 

Battery Charging 

The battery should only be charged with Sepura plc approved 
battery  chargers.  Failure  to  use  an  approved  battery  charger 
will invalidate the warranty of the battery and the hand-held. 

A range of battery chargers is available that allow the battery 
to  be  charged  while  fitted  to,  or  removed  from,  the  hand-held 
(depending  upon  the  charger  model  and  hand-held  type 
selected).  When  the  battery  is  fitted  to  the  hand-held,  the 
battery can be charged via the facility connector located at the 
base of the hand-held. If the battery is charged with the hand-
held  switched  on,  the  time  remaining  to  charge  the  battery  to 
its full capacity is shown on the hand-

held‟s display.

 

 

When  charging,  the  colour  of  the  LED  on  the  hand-held 
indicates the progress of battery charging: orange shows charging in progress, green shows 
charging  complete,  red  shows  charging  failure.  A  fully  discharged  battery  may  not  provide 
enough  power  to  support  the  hand-held  display  during  the  initial  phases  of  charging. 
However, when sufficient power is available, the display will operate. 

 

 

The battery includes circuitry to protect against damage caused by accidental shorting 
of the contacts. Once the battery has protected itself, it will not operate again until it 
has been removed from the hand-held and charged. 

 

The  hand-held  warns  the  User  of  a  Low  battery  condition  by 
displaying  the  Low  battery  Icon  and  repetitively  flashing  the 
Red LED for 1 second at 1 second intervals. The Battery Level 
indicator at the left hand side of the screen is also displayed in 
red on the SRH3800 and SRH3900 radios. 

 

As with all batteries, charging cycles reduce the cell capacity.  The battery is specified to have 
retained a nominal 80% of its original fully charged capacity after 500 charge cycles. Charging 
must be conducted using a Sepura approved charger. 

 

 

Batteries have a finite life; they deteriorate if they are not charged on a periodic basis.  
Batteries should not be left for more than 6 months without recharging as the cells will 
deteriorate and the batteries will not be recoverable. 

 

Many  professional  and  consumer  products  from  cycle  lamps  to  mobile  phones  and  laptop 
computers now use rechargeable lithium-ion (Li-ion) cells because of their small size and high 
energy  density.    When  charged  and  used  correctly  these  are  reliable  and  safe.  There  are 
some simple precautions that should be observed when charging and using Li-ion packs. The 
precautions below apply to most/all Li-ion battery packs and chargers. 

1.  Properly  designed  Li-ion  batteries  and  chargers  contain  effective  protection  circuitry  to 

safeguard  the  pack  during  charging  and  use,  but  in  some  very  rare  circumstances  of 
internal cell failure during charging, the protection circuits may be ineffective and the pack 
may  overheat.    To  minimise  the  chance  of  this  causing  further  damage,  Li-ion  battery 
chargers  should  be  used  in  well  ventilated  areas  away  from  combustible  material.    For 

example, don‟t charge your TETRA battery, mobile phone battery or laptop battery with 

the battery and charger very near to curtains, soft furnishings, paper or other combustible 
material. 

Содержание STP8000 Series















































Отзывы: