SEPTENTRIO PolaRxS Скачать руководство пользователя страница 12

Страница: 12 / 13

_______________________________________________________________________ 1 PolaRxS_PRO

PolaRxS Product Family Hardware Manual v1.3.0

pauses
blinks 5 times, then
pauses

9 or more

1.5

Cables

Cable Name: CBLe_COM_1,8

Part #: 200416

This cable can be connected to either the COM1 or COM2 connector. Note that RTS/CTS lines are
only available when connected to COM2.

Cable Name: CBLe_GPO_OE_5

Part #:

201203

Open-ended cable to be used with the OUT connector (see pinout in section 1.2.5).

Pin#

Wire Color

Blue

Blue/Black

Orange

Green

Brown

Cable Name: CBLe_GPI_OE

Part #:

200419

Open-ended cable to be used with the IN connector (see pinout in section 1.2.6).

Pin#

Wire Color

Orange

Green

Yellow

Black

Red

Purple

Brown

Do not leave the red and purple wires floating. Tie them to ground if not used. This is to avoid

crosstalk effects that could lead to spurious level transitions on the EventA and EventB inputs.

Cable Name: CBLe_USB

Part #:

201202

USB cable to be connected to the COM3-4/USB connector.

Cable Name: CBLe_ETH_MS

Part #:

200418

Ethernet cable (straight) to be connected to the ETH connector.

Cable Name: CBLe_ETH_MX

Part #:

200417

Содержание PolaRxS














Результаты поиска

Содержание PolaRxS

Отзывы:

Похожие инструкции для PolaRxS

Бренды по названию

Популярные бренды

SEPTENTRIO PolaRxS, Руководство по оборудованию

Результаты поиска

Содержание PolaRxS

Отзывы:

Похожие инструкции для PolaRxS

Бренды по названию

Популярные бренды