SEP LEM012SD Скачать руководство пользователя страница 7

7                                                                                               

SEP LEMO12SD / LEM012SS 2015 

device for the meter must be installed on the supply side, and it is 
recommended that the overcurrent protection device is near the meter so that it 

is convenience for the operator. The overcurrent protection device should 
comply with the specifications of the building electrical design and all local 
regulations. 

This meter can be installed indoor directly, or in a waterproof meter-box outdoor, 
in compliance with the local codes and regulations. 

The meter has to be installed in a good ventilated and dry place. 

The meter has to be installed in a protection box in dangerous or dusty 
environment. 

The meter can be installed and used after being tested in accordance with the 
specifications of the building. 

The meter can be installed on a 35mm DIN rail. 

The best way to install in an available height so that it is easy to read. 

When the meter is installed in an area with frequent surges due to e.q. 
thunderstorms, welding machines, inverters etc, protect the meter with 

apllicable Surge Protection Devices. 

After finishing installation, the meter must be sealed to prevent tampering. 

 

Connection of the wires should be done in accordance with the underneath 
connection diagram. 

 

1

4

L

N

3

6

20

S O

21

+

-

 

 

1              

  Inlet phase line 

4               

  Inlet neutral line 

       

  Outgoing phase line 

6               

  Outgoing neutral line 

20 and 21    Pulse output contact 

 
 

1.9    Operating 

 

Working indication 

There is a white LED which has two colors (green and red) while burning in the front 

panel  of  LEM012SD  and  LEM012SS.  When  the  meter  works  normally,  this  LED  will 
display green. When meter is going wrong or no power supply, the LED will turn off. 

 

Consumption indication 

There is a white LED which has two colors (green and red) while burning in the front 

panel of LEM012SD or LEM012SS. When consumption happens, the LED will flash and 
display red. The more quickly LED flash, the more consumption there is. For this LED, 
the flash rate is 2000 impulses per kWh (0.5Wh/imp). 

 

Reading the meter

 

LEM012SD  /  LEM012SS  is  equipped  with  a  white  backlight  LCD  display.  During  the 

normal working hours, the meter will be burning this white backlight all the time. The 
display will show the following energy data and indication message. 

Содержание LEM012SD












Отзывы: