Sentry Saf-T-Vise STV-LP1 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 20

Sentry Saf-T-Vise STV-LP1 Скачать руководство пользователя страница 4

4

Sentry Equipment Corp

Safety Information

Please read the entire manual before attempting to unpack, set up, or operate this product . Pay careful attention to all

Warnings, Cautions, and Notes . Failure to do so could result in serious personal injury and/or equipment damage .

Use of Hazard Information

If multiple hazards exist, the signal word corresponding to the greatest hazard shall be used .

Defi nitions

DANGER

indicates a hazardous situation which, if not

avoided, will result in death or serious injury .

WARNING

indicates a hazardous situation which, if not

avoided, could result in death or serious injury .

CAUTION

, used with the safety alert symbol, indicates a

hazardous situation which, if not avoided, could result in

minor or moderate injury .

NOTICE

is used to address practices not related to personal

injury .

Â

NOTE

Information that requires special emphasis .

Â

TIP

Alternate techniques or clarifying information.

SHALL:

This word is understood to be mandatory .

SHOULD:

This word is understood to be advisory .

«
...
2
3
4
5
6
...
»

Содержание Saf-T-Vise STV-LP1





















Отзывы:

Нет отзывов