background image

www.sentera.eu

MIW-RTVS1-EN-000 - 03 / 11 / 2020

4 - 12

back to the table of contents

back to the table of contents

PRODUCT DESCRIPTION

The RTVS1 series of transformer fan speed controllers regulate the rotational speed 
of single-phase voltage controllable motors in five steps by varying the output 
voltage. They are equipped with auto-transformer(s) and feature Modbus RTU 
communication, TK monitoring for thermal motor protection. 

ARTICLE CODES

Article code

Rated max.  current  [A]

Fuse [A]

Current rating, no load [A]

RTVS1-15L22

1,5

T-2,5 A-H

0,04

RTVS1-25L22

2,5

T-4 A-H

0,06

RTVS1-35L22

3,5

T-5 A-H

0,08

RTVS1-50L22

T-8 A-H

0,1

RTVS1-75L22

7,5

T-10 A-H

0,12

INTENDED AREA OF USE

 

 Fan  speed  control  of  voltage  controllable  motors  (pumps  and  fans)  in  ventilation            
systems

 

Demand based ventilation in greenhouses, sheds and stables.

 

 Ventilation based on temperature, relative humidity, carbon dioxide, air quality 
(TVOC) or carbon monoxide*

 

    For  indoor  use,  surface  mounted

*Selection can be made via RTVS1 Modbus holding register 20.

TECHNICAL DATA

 

 Supply voltage: 230 VAC / 50—60 Hz

 

Modbus RTU communication

 

TK monitoring for thermal motor protection

 

Operating modes:

 

 Automatic (from low to high or from high to low): Fan speed based on input from 

external Sentera sensor or potentiometer connected to the RJ45 master socket

 

 Manual: Fan speed based on user input via Modbus Holding Register 12

 

Selectable output update interval from 5 s to 10 min

 

LED status indication

 

Modbus RTU communication via RJ45 connectors

 

Unregulated output 230 VAC (I max 16 A, resistive load)

 

Bootloader for uploading new firmware via Modbus RTU

 

Enclosure: plastic (R-ABS, UL94-V0, grey RAL 7035)

 

Protection standard: IP54 (according to EN 60529)

 

Operating ambient conditions:

 

Temperature: -10—35 °C

 

Rel. humidity: 5—85 % rH (non-condensing)

STANDARDS

 

Low Voltage Directive 2014/35/EC: 

 

 

 

 

EN 60529:1991 Degrees of protection provided by en-closures (IP Code) 

Amendment AC:1993 to EN 60529

 

 EN 60730-1:2011 Automatic electrical controls for household and similar use - 

Part 1: General requirements

TRANSFORMER FAN SPEED CONTROLLER WITH 
MODBUS RTU COMMUNICATION

RTVS1

Содержание RTVS1













Отзывы: