Sentera Controls EVSS Series Скачать руководство пользователя страница 4

Страница: 4 / 16

www.sentera.eu

MIW-EVSS-DM-EN-000 - 18 / 12 / 2018

4 - 16

PRODUCT DESCRIPTION

The EVSS1 is an electronic speed controller which controls the speed of single-
phase (230 VAC / 50—60 Hz) voltage controllable electric motors. It is equipped
with Modbus RTU (RS485) communication, an alarm relay output and thermal
contacts to provide overheating protection of motors with cut-out contacts. The
EVSS controller provides a wide range of functionalities: remote control options,
adjustable off level, min. and max. output voltage settings, and time-limited motor
operation initiated by a logic or switch signal.

ARTICLE CODES

Code

Nominal current, [A]

Fuse rating, [A]

EVSS-1-15-DM

1,5

(5*20 mm) F 3,15 A H 250 VAC

EVSS-1-30-DM

3,0

(5*20 mm) F 5,0 A H 250 VAC

EVSS-1-60-DM

6,0

(5*20 mm) F 10,0 A H 250 VAC

EVSS-1100-DM

10,0

(6,3*32 mm) F 16,0 A H 250 VAC

INTENDED AREA OF USE

■

Fan speed control in ventilation systems

■

For indoor use only

TECHNICAL DATA

■

Power supply: 230 VAC ±10 % - 50—60 Hz

■

Analog input:

►

voltage: 0—10 VDC / 10—0 VDC

►

current: 0—20 mA / 20—0 mA

■

Analog input modes: ascending or descending

■

Analog input functionality: Normal mode / Logic mode

■

Remote control input: normal or timer functionality

■

Regulated output: 30—100 % Us

■

Max. output load: depends on the version

■

Unregulated output, L1: 230 VAC (50 / 60 Hz) / max. 2 A

■

Alarm output (230 VAC / 1 A)

■

Min. output voltage setting, Umin: 30—70 % Us (69—161 VAC), selectable by
trimmer or via Modbus

■

Max. output voltage setting, Umax: 75—100 % Us (175—230 VAC), selectable by
trimmer or via Modbus

■

Off level, adjustable by trimmer or via Modbus:

►

0—4 VDC / 0—8 mA for ascending mode

►

10—6 VDC / 20—12 mA for descending mode

■

Kick start or soft start

■

Low voltage supply output: +12 VDC / 1 mA for external potentiometer

■

Modbus communication

■

Operating indication:

►

continuous green: normal operation

►

blinking green: stand-by

■

Overvoltage and overcurrent protection

■

Thermal inputs for motor overheating protection

EVSS

ELECTRONIC FAN SPEED
CONTROLLER WITH TK

Содержание EVSS Series

















Результаты поиска

Содержание EVSS Series

Отзывы:

Похожие инструкции для EVSS Series

Бренды по названию

Популярные бренды

Sentera Controls EVSS Series, Монтаж и эксплуатация

Результаты поиска

Содержание EVSS Series

Отзывы:

Похожие инструкции для EVSS Series

Бренды по названию

Популярные бренды