manualshive.com logo in svg

Sensotec Rapidox 1100ZR-H-OL-LC, Инструкция по эксплуатации

Поделиться
Скачать
Sensotec Rapidox 1100ZR-H-OL-LC Скачать руководство пользователя страница 49

D11-044-1:  Rapidox 1100ZR-H-OL-LC O

2

 Analyser Instruction Manual 

 

 

D11-044-1 

43 

Last printed 08/11/2016 12:10:00 

 
 

9

 

Appendix : Heller Specific Software Features 

 

9.1

 

SW Alarm Config tab 

 

 

 

Figure 23: Software Alarm Config tab 

 
The SW (software) Alarm Config tab allows the user to set alarms in software to be 
used by a DDE (Dynamic Data Exchange).  The settings here create links for the 
DDE to interpret using the standard protocol as listed in 9.2 below.  For single gas 

instruments such as the Rapidox 1100ZR only the parameters for channel 1 are 
used.  For the Rapidox 1100ZR3 (multichannel) all three channels can have 
software programmed alarms defined. 
 
1)

 

Channel 1 Alarms:

  Select an option from Enabled or Disabled to activate 

the alarms on this channel.  The default is Disabled. 
 

2)

 

CH1 Alarm 1 Set Point:

 The current units (% or ppm) are displayed by the 

text and can be changed using the “Units” drop down menu.  Enter a set 
point for the first software alarm here.  For example, for an alarm set point 
at 30% O

2

, enter “30” into the edit box.  Note that alarm 1 is triggered when 

RISING above this value. 
 

3)

 

CH1 Alarm 2 Set Point:

  Enter a set point for the second software alarm 

here.  For example, for an alarm set point at 0.01% O

2

, enter “0.01” into the 

edit box.  Note that alarm 2 is triggered when FALLING below this value. 
 

If you are working with a Rapidox 1100ZR3 with three gas inlets then repeat this 
process for the remaining channels 2 and 3.  Otherwise these additional boxes 

remain greyed out. 

 

Содержание Rapidox 1100ZR-H-OL-LC
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды