manualshive.com logo in svg

Sensotec Rapidox 1100ZR-H-OL-LC, Инструкция по эксплуатации

Поделиться
Скачать
Sensotec Rapidox 1100ZR-H-OL-LC Скачать руководство пользователя страница 26

D11-044-1:  Rapidox 1100ZR-H-OL-LC O

2

 Analyser Instruction Manual 

 

 

D11-044-1 

20 

Last printed 08/11/2016 12:10:00 

 
 

5.15.2

 

RS485 protocol 

 

Please contact Cambridge Sensotec for further information on this feature. 
 

5.16

 

Printing 

 

If you have purchased the printer option then you have the option to print out 
various data from the analyser straight on to thermal paper.  Simply connect the 
printer to the unit using the serial socket on the rear of the machine and make 

sure the printer is switched on (battery and mains versions are available).  To 
print the live values on the LCD at any time simply press the RIGHT arrow button 
on the front panel.  Each push of the button will print out the serial number 
followed by the data in a tabbed format followed by a blank line.  If the button is 
held down, the printer will keep printing data (but not the serial number). 

 
When the printer is first connected or turned on, a “start-up” message like the one 
displayed on the LCD when the Rapidox is switched on will be printed, and will 
look like this: 
 

Cambridge 

Sensotec Ltd 

Rapidox 1100ZR-H-OL-LC 

Oxygen Analyser 

S/N: 2100942 

FW v 01.03.03.01 

 

5.17

 

Load Defaults 

 

If you make a mistake programming the Rapidox it is possible to restore the 
machine back to its factory settings by loading the unique default configuration 
that is supplied on your software memory stick.  The default set-up can only be 

accessed using the software provided.  Please see section 7.23 for further details. 
 
Alternatively, you can reset to ‘generic’ factory defaults directly from the front 
panel keypad.  Press ENT to enter the user setup menu and select menu option 10 
“Load Defaults” and press ENT to proceed.  The next screen will say “Load 

Defaults ?” with the prompt to press and hold ENT for 2 seconds to confirm.  To 
complete this press the ENT button until the bar graph has completed and the 
screen says “Defaults Loaded”  This will give you all the basic settings that are 
factory set.  You will now need to re-calibrate the sensor and check all the settings 
are suitable.  

 
 
 

 

Содержание Rapidox 1100ZR-H-OL-LC
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды