manualshive.com logo in svg

Sensotec Rapidox 1100ZR-H-OL-LC, Инструкция по эксплуатации

Поделиться
Скачать
Sensotec Rapidox 1100ZR-H-OL-LC Скачать руководство пользователя страница 10

D11-044-1:  Rapidox 1100ZR-H-OL-LC O

2

 Analyser Instruction Manual 

 

 

D11-044-1 

4 

Last printed 08/11/2016 12:10:00 

 
 

5.1

 

Open Loop Connections 

 

On the rear of the OL coded machines is a terminal “Supply Valve (In) terminal for 
connecting a signal voltage from the oven to indicate when the oven is operating. 

 

 

Figure 3: Rear Panel Terminal Strip 

 

1)

 

Supply Valve (In):

  This connection requires a 12-24V connection from the 

oven to indicate when it is operation.  The analyser sample pump is 
disabled when there is no voltage signal present. 

 

5.2

 

The Rapidox Analyser - Menu System 

 

All of the user-programmable functions are accessed via a menu system which is 
controlled using the front panel Keypad (2).  To access the menu press the ENT 
button and to escape and return to the operating screen press ESC at any time.  

The menu system flow chart is shown in Appendix 1 below: 
 

5.3

 

Getting Started 

 

Ensure that the Rapidox analyser is located away from extreme heat and dirt 
environments.  Plug the unit in to a suitable supply (noting the information on the 
serial sticker and using the power cable supplied) using the rear power socket (8).  
Make sure that the cooling fan (9) is not obstructed during operation.   

 
Push the gas sample tube (6mm OD/4mm ID) to the GAS IN (3) connector and fit 
the retaining collar hand tight.  Repeat for the GAS OUT (4) connector should an 
outlet tube be required.  The pump will draw gas at a flow rate depending on the 
value set either in the software or from the menu.  The default setting is one 

hundred percent. 
 
Turn the unit on using the red power switch on the front (5).  The LCD (1) will 
display the firmware version followed by the message “HEATING SENSOR”.  The 
sensor will take approximately one minute to come up to temperature, after which 

the Rapidox will begin to take measurements.  The progress of the sensor heater is 
shown in the form of a bar graph on the LCD (1).  Once at temperature the LCD 
display will show the oxygen reading and the pressure.  The symbol AL1 or AL2 
may appear to the bottom right of the LCD if the alarm system is enabled and an 
alarm condition applies. 

+ve 

-ve 

1

 

 

 

Содержание Rapidox 1100ZR-H-OL-LC
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды