Seneca ZC-24DO Скачать руководство пользователя страница 1

Страница: 1 / 8

Z-PC Line

ZC-24DO

CANopen/MODBUS I/O Module

24 Digital Outputs

Installation

Manual

Contents:

- General Specifications

- Technical Specifications

- Installation Rules

- Electrical connections

- DIP-switches settings

- Programming

- Significant Components Position

- Leds Signallings

- Factory Settings

SENECA s.r.l.

Via Austria, 26 - 35127 - PADOVA - ITALY

Tel. +39.049.8705355 - 8705359 - Fax +39.049.8706287

For manuals, EDS files and configuration software, see www.seneca.it

This document is property of SENECA srl. Duplication and reprodution are forbidden, if not

authorized. Contents of the present documentation refers to products and technologies described in it.

All technical data contained in the document may be modified without prior notice Content of this

documentation is subject to periodical revision.

MI001523-E

ENGLISH 1/8

Содержание ZC-24DO









Результаты поиска

Содержание ZC-24DO

Отзывы:

Похожие инструкции для ZC-24DO

Бренды по названию

Популярные бренды

Seneca ZC-24DO, Руководство по установке

Результаты поиска

Содержание ZC-24DO

Отзывы:

Похожие инструкции для ZC-24DO

Бренды по названию

Популярные бренды