Seneca Z109TC2-1, Руководство по установке

Страница: 6 / 8

ENGLISH - 6/8
SETUP USING THE DIP-SWITCHES
The type of input is selected using DIP-switch SW1 at the side of the module.
Each type of input corresponds to a certain number of scale start and end values that can be selected
through the Sw2 group.
The table below shows the possible START and END values based on the selected input type; the left
column shows the DIP-switch combination to set for the selected START and END.
CAUTION
The DIP-switches must be set with the
power supply disconnected, to avoid
electrostatic discharges and damage
to the module.
(*)START and END set in the memory using the PC or programming buttons;
(2) Zero output for t < 250°C.
CAUTION
The set START values (scale start) must never be higher than the set END values (scale end). Otherwise
an error status will occur, indicated by the yellow LED.
t
SW1: SELECT THE THERMOCOUPLE TYPE
POSITION INPUT POSITION INPUT
1 2 3 4 TYPE 1 2 3 4 TYPE
Tc J Tc T
Tc K Tc B
Tc R Tc E
Tc S Tc N
KEY ON OFF
Tc J Tc K Tc R Tc S Tc T Tc B (2) Tc E Tc N
(*) (*) (*) (*)
-200 °C -200 °C 0 °C 0 °C
-100 °C -100 °C 100 °C 100 °C
0 °C 0 °C 200 °C 200 °C
100 °C 100 °C 300 °C 300 °C
200 °C 200 °C 400 °C 400 °C
300 °C 300 °C 600 °C 600 °C
500 °C 500 °C 800 °C 800 °C
(*) (*) (*) (*)
-200 °C 0 °C -200 °C
-200 °C
-100 °C 500 °C -100 °C
-100 °C
-50 °C 600 °C 0 °C 0 °C
0 °C 700 °C 100 °C 100 °C
50 °C 800 °C 150 °C
200 °C
100 °C 1000 °C 200 °C
300 °C
150 °C 1200 °C 400 °C 500 °C
SW2:START
1 2 3
THERMOCOUPLE TYPE
(*) (*) (*) (*)
100 °C 200 °C 400 °C 400 °C
200 °C 400 °C
600 °C 600 °C
300 °C 600 °C
800 °C 800 °C
400 °C 800 °C 1000 °C 1000 °C
500 °C 1000 °C 1200 °C 1200 °C
800 °C 1200 °C
1400 °C 1400 °C
1000 °C 1300 °C
1750 °C 1750 °C
Tc J Tc K Tc R Tc S Tc T Tc B (2) Tc E Tc N
(*)
(*)
(*) (*)
50 °C
500 °C
50 °C 200 °C
100 °C 600 °C 100 °C 400 °C
150 °C 800 °C 200 °C 600 °C
200 °C
1000 °C
300 °C 800 °C
250 °C
1200 °C
400 °C 1000 °C
300 °C 1500 °C 600 °C 1200 °C
400 °C 1800 °C 800 °C 1300 °C
4 5 6
SW2:END THERMOCOUPLE TYPE