background image

ENGLISH 2/7

1 PRELIMINARY WARNINGS 

Before  performing  any  operation,  it  is  mandatory  to  read  and  understood  in  full  the 
contents  of  this  installation  manual.  The  module  may  only  be  used  by  qualified  and 
skilled  technicians  in  the  field  of  electric  installations.  Specific  documentation  is 
available at website: 

www.seneca.it/products/z-tws11

 

Only the Manufacturer is authorized to repair the module or to replace damaged parts. 
The  product  is  susceptible  to  electrostatic  discharge,  take  appropriate 
countermeasures during any operation

The user must comply of the safety instructions in this installation manual, the country-
specific  installation  standards  and  all  prevailing  safety  regulations  and  accident 
prevention  rules.  No  warranty  is  guaranteed  in  connection  with  faults  resulting  from 
improper use, from modifications or repairs carried out by Manufacturer-unauthorized 
personnel on the device, or if the content of this user Manual is not followed.

 

2 PRELIMINARY INSTRUCTIONS 

It is forbidden 

block the ventilation slots with any object.

 

It is forbidden to install the module near heat sources. 

Warning:

 

Do not turn off the Z-TWS 11 module while writing the micro SD card so as not to 

corrupt the file system.

 

For data logging applications on micro SD card, you must use an external UPS.

 

3 GENERAL SPECIFICATIONS 

Multifunction and multi-protocol control unit

.

Module configuration and firmware upgrade through Web-server

Integrated Straton PLC.

Insulation 1500 V

A

 between power supply and other circuits

Easy power supply and serial communication wiring through Seneca IEC EN 60715 DIN rail bus

Removable terminals with section of 2.5 mm

2

.

LEDs signaling: power on, micro SD card access, Ethernet link and activity, RS485 Rx and Tx

2 analog inputs at 16 bit configurables for voltage or current.

1 Ethernet RJ45 front. 10/100 Mbps, 1 RS485 Port, 1 RS232/RS485 Port, 1  Micro USB

Supported System Protocols: 

FTP client, SMTP client, http, ModBUS TCP, ModBUS RTU

RAM retentive variables max.= 4 kByte (Fe-RAM 

technology with limitless writes

)

Micro SD additional storage memory up to 32 GB

ARM Processor 120 MHz, 32 bit, Real Time multitasking O.S.

MI00367

-3

-E 

Содержание Z-TWS11








Отзывы: