background image

ENGLISH 7/8

MI003651-E

Default Conditions

Module factory settings parameters:

SW1 Switch position

ON

 

LED Signallings

LED

STATE

Meaning of LEDs

PWR Green

On

The module is power on

Stop/Run 

On

The module is ready for use

Fault Red

On

O.S. boot loading

Run1-2 Yellow

Blinking

There is data activity (Ethernet 1-2)

Lnk1-2 Green

On

Ethernet 1-2 connection detected

TX1-2-3 Red

Blinking

Signaling Data Transmitting (COM 1-2-3)

RX1-2-3 Red

Blinking

Signaling Data Receiving (COM 1-2-3)

TX1-2-3 Red

On

Verify the connection (COM 1-2-3)

RX1-2-3 Red

On

Verify the connection (COM 1-2-3)

Plug-in Connector for Micro SD Card

Micro SD card

The  Z-TWS5  has  a  slot  for  micro  SD 
card placed on the side of the case
Before pushing the SD card in this slot, 
please be sure that the SD card metal 
contacts are facing towards left (Please 
see the figure on side).

SD card
metal
contacts

Micro SD Card

DIP-Switch SW1

ON RS485 COM2

OFF CANopen COM0

On the module side there are one switch. 
With this switch you can choose between 
RS485  or  CANopen  serial  interfaces, 
from  screw  terminals  1-2-3  or  from  the 
rear side 10 pin connector.

 We suggest 

to  turn  off  the  module  before  setting 
the switches.

Содержание Z-PC Z-TWS5









Отзывы: