background image

MI00146 -E

2

ENGLISH - 4/8

Before using the instrument, verify in the rear label if the indicator has already been set by 
the factory, for a particular input signal and a specific display view.
In this case a label is present on the calibration panel where the following informations are 
listed:

-

the scale of display view.

If no label is present, the instrument has the following factory settings: 
- Output: 0..20 mA
- View scale: 0..19,99

Decimal Point Selection :

P1: one decimal, P2: two decimals

P3: three decimals

SETTING OF THE DECIMAL POINT

Three jumpers, placed in the rare of the frontal panel, define the position of the decimal 
point:

FA TORY SETTINGS

C

SENECA s.r.l.

Via Austria, 26 - 35127  -  PADOVA - ITALY
Tel.  +39.049.8705355 - 8705359  -  Fax +39.049.8706287
e-mail: [email protected]  -  www.seneca.it

THE INTERNATIONAL CERTIFICATION NETWORK

R

ISO9001-2000

This document is property  of SENECA srl. Duplication and reprodution are forbidden, if not authorized. Contents 
of the present documentation refers to products and technologies described in it. All technical data contained in the 
document may be modified without prior notice Content of this documentation is subject to periodical revision.

Disposal of Electrical & Electronic Equipment (Applicable throughout the European Union and 
other European countries with separate collection programs)
This symbol, found on your product or on its packaging, indicates that this product should not be 
treated as household waste when you wish to dispose of it. Instead, it should be handed over to an 
applicable collection point for the recycling of electrical and electronic equipment. By ensuring this 
product  is  disposed  of  correctly,  you  will  help  prevent  potential  negative  consequences  to  the 
environment and human health, which could otherwise be caused by inappropriate disposal of this 
product.  The  recycling  of  materials  will  help  to  conserve  natural  resources.  For  more  detailed 
information about the recycling of this product, please contact your local city office, waste disposal 
service or thè retail store where you purchased this product.

P3 P2 P1

Содержание S201D









Отзывы: