SENDER RAMPS PROGRESSION Series Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 24

SENDER RAMPS PROGRESSION Series Скачать руководство пользователя страница 14

REPEAT THE PROCESS ABOVE TO COMPLETE THE SECOND PART OF YOUR 1200 TABLETOP. CHECK THE SMOOTH FUNCTION OF

THE END PLATES. THEY SHOULD FOLD EASILY AND RETURN TO A VERTICAL POSITION.

RE-JOINING YOUR ASSEMBLED TABLETOP

You may have purchased you Tabletop Assembled. You must follow these steps to join the parts back together. It will arrive in
COMPACT shipping / transport and storage mode. Place the two parts together on a flat surface to check the alignment of the
vertical ends. Stand the two parts on one edge / side as shown below.

Take the two long joining plates with 4 holes and align this over the holes in the side panels. Place 4 x M10 x 35 Countersink
bolts into the holes by finger and then tighten the bolts to 12 Nm. Carefully turn the Tabletop over and repeat on the other side
tightening the fixing bolts to 12 Nm. Before proceeding check that all screws and bolts are secure. Your Tabletop is now ready to
place between two ramps of the same height or attach legs of a chosen length.

«
...
12
13
14
15
16
...
»

Содержание PROGRESSION Series

























Отзывы:

Нет отзывов