Senco DS212-18V Скачать руководство пользователя страница 8

 

Safety Warnings 

8

l

 

Do not operate charger with  

damaged cord or plug- replace 

them immediately.

l

 

Do not operate charger if it 

has received a sharp blow, 

been dropped, or otherwise 

damaged in any way; take 

it to a SENCO Authorized 

Service Center.

l

 

Do not disassemble charger 

or battery cartridge; take 

it to a SENCO Authorized 

Service Center when service 

or repair is required. Incorrect 

reassembly may result in a risk 

of electric shock or fire.

l

 

To reduce risk of electric 

shock, unplug charger from 

outlet before attempting any 

maintenance or cleaning.

l

 

Store battery packs in a 

30%-50% charged condition.

l

 Every six months of storage, 

charge the pack as normal.

For best results, your 

battery should be charged 

in a location where the 

temperature is more than 50˚F 

but less than 100˚F. Do not 

store outside or in vehicles.

An extension cord should not 

be used unless absolutely 

necessary. Use of improper 

extension cord could result in a 

risk of fire and electric shock. If 

extension cord must be used, 

make sure:

a. That pins on plug of

extension cord are the same 

number, size, and shape as 

those of plug on charger;

b. That extension cord is

properly wired and in good 

electrical condition; and 

c. That wire size is at least as

large as the one specified in 

the table.

Length of Cord (Feet)

  25     50     100     150

AWG Size of Cord

  16     16       16       14

Largo del cable (m [pies])

  7,5    15       30       45

Calibre AWG del cable

  16     16       16       14

Longueur du cordon (en m)

  7,5    15       30       45

Taille AWG du cordon

  16     16       16       14

TABLE 1

RECOMMENDED MINIMUM 

AWG SIZE FOR EXTENSION 

CORDS FOR BATTERY 

CHARGERS

Содержание DS212-18V




















Отзывы: