manualshive.com logo in svg

Select Four 10SC, Руководство пользователя и техническая информация, Страница: 7 / 42

Поделиться
Скачать
Select Four 10SC Скачать руководство пользователя страница 7

7

Getting Started

Below are some steps to help get you going right away and most applicable 

to those who have used RC products before. If you are new to the hobby or 

it has been a while since you’ve worked with the latest technology, please 

read through the manual to acquaint yourself with the latest procedures, 

Warnings, Cautions and Tips.

Charging

Although this information should be included with your batteries and charger, 

we have included it here again to ensure you have seen it and are aware 

of the most common things to be aware of with regards to charging our 

batteries.

•  Never leave the battery unattended while charging and never operate the 

charger without adult supervision.

•  Never charge a warm battery, always allow the battery to cool to room 

temperature before charging.

•  Never drop the charger or battery and do not attempt to charge a 

damaged battery.

•  Inspect the battery and charger before use. Never use a battery or 

charger if the wire or connector has been damaged or if the battery has 

experienced a short.

•  Incorrect use of the battery, connections, or charging equipment can 

cause personal injury or property damage.

•  Never allow batteries or charger to come in contact with moisture at any 

time.

•  Stop charging immediately if the battery or charger becomes hot or 

changes form during use.

WARNING:  WHEN USING LIPO BATTERIES, ONLY USE CHARGERS DESIGNED 

FOR USE WITH LIPO BATTERIES FOR THE RC INDUSTRY THAT ENABLE BALANCE 

CHARGING AND USE THE SUPPLIED CONNECTOR. USE OF OTHER (NON-RC 

SPECIFIC) CHARGERS OR CONNECTORS CAN CAUSE CATASTROPHIC FALURES AND 

CAUSE PERMANENTLY DAMAGE YOUR BATTERY AND/OR CONNECTED EQUIPMENT. 

THIS PRODUCT IS NOT A TOY AND SHOULD NOT BE CHARGED, OPERATED, OR 

MAINTAINED WITHOUT SUPERVISION OF AN ADULT.

Fully balance charge your chosen 2S or 3S LiPo battery in accordance with 

charging and safety guidelines supplied with the battery. LiPo batteries are 

sensitive to the charge current and as such, it should be chosen with care.

•  The battery pack must have a compatible HCT plug, never use plug 

adapters that include a non-high-current connector.

•  You can use a suitable NiMH battery pack, however you must change 

the LVC (low voltage cut-off) on the ESC (see Appendix at the back of this 

manual for ESC settings)

Содержание Four 10SC











































Отзывы:

Нет отзывов