Level 1
Level 2
Display
Display
Default
Value
Default
Value
Range
Range
J/K/T/R/S/RTD
1/0.1
1.0 to 400.0°
°
C/
°
F
0 to 9999 sec
Min range of sensor
selected to SPHL
0 to 9999 sec
SPLL to Max range
of sensor selected
AUTO/USR.F
0.2 to10.0 sec
0.1 to 99.9 sec
0.1 to 99.9 sec
RE/FD
RE/FD/TIME
NO/YES
0.1 to 99.9
°
0.1 to 99.9
°
PID/ONF
RELAY/SSR
-19.9 to +19.9
°
1.0 to 400.0
°
NO/YES
OFF, 1 to 9999 min
-19.9 to 19.9
°
Display
Condition
Display
Condition
Not prompted
for R & S type
For CNTL=ONF
For HC=NO or
HC=YES &
CNTL=ONF
For CNTL=PID
& I=0
Description
Input type
(Refer Table 1)
Tune
(Refer user guide)
Display Resolution
Proportional band
Temperature unit
Integral time
Set point low limit
Derivative time
Set point high limit
Cycle time mode
Cycle time
Cycle time-cool
Control action for
relay 1
Control action for
relay 2
Factory default
(Reset all)
Hysteresis 1
Hysteresis 2
Control logic
Control Output selection
Dwell mode enable
Manual reset
Proportional
band-cool
Heat-cool mode
selection
POWER ON
OPERATIONAL MENU
Description
Dwell time
Display bias
Filter time constant
NO/YES
When HC=NO.
TIME prompted
when DWEL
=YES
When DWEL
=YES
When CNTL
=PID
REMN/ELPS
1.0 to 100.0%
Online menu for timer
Anti-reset windup %
DEV/ABS
Relay 2 type
When
ACT2=RE/FD
For CNTL=PID
For CNTL=PID
For CNTL=PID
For CNTL=PID
For CNTL=PID
For CNTL=PID
For CNTL=PID
&
HC=YES
When DWEL
=YES
CONFIGURATION INSTRUCTIONS
Press once to view online parameters
Press for 3 sec to enter Level 2
Press once to view next parameter in configuration menu
Press for 3 sec to view Level 1
Press once to view previous parameter in configuration menu
+
or
+
Allows the user to increase or decrease associated parameter value
or
or
+
To exit configuration menu press any of these keys for 3 sec
+
Press for 3 sec to enter protection Level
Not prompted
for HC=YES
Protection Level
Display
Default
Value
Range
UNLK/READ
Display
Condition
Lock setpoint 1
Lock level 1
Lock level 2
Lock dwell time
Description
Prompted when
DWEL=YES
Note
UNLK/READ/LOCK
UNLK/READ/LOCK
UNLK/READ/LOCK
UNLK/READ/LOCK
Lock setpoint 2
Press key for 3sec.
Press + keys for 3sec.
1. Locking parameters (LVL1 or LVL2 or SP or DWEL) will not permit
change in the value of respective level parameters.
Time value (online) can be altered only when DWEL is not locked
in protection level.
2. Continuous operation of + / keys for SP or other parameters
makes update speed faster in 3 stages after 3 sec.
For CNTL=PID
&
HC=YES
Note :
At power ON lower display shows (momentary) input type selected in Level 1.
Press key for 3sec.
K
E
Y
F
U
N
C
T
IO
N
S
OFF / ST / AT
1
T
2
S
TC544
Doc. Name : OP INST TC544C OP723-V03(Page 3 of 4)
YES/NO
