Sel SEL-2600 Скачать руководство пользователя страница 6

SEL-2600 RTD Module

Date Code 20000525

SEL-2030 Communications Processor Applications

6

SEL-2030 
Communications Processor Applications

Use the SEL-2600 RTD Module in combination with the SEL-2030 Commu-

nications Processor to enhance many protection and monitoring applications. The 
SEL-2030 monitors temperature data from the SEL-2600, performs threshold com-
parisons, and sends control commands to a protective relay.

The applications shown in Figure 2Figure 3, and Figure 4 on page 7 repre-

sent a few of the possible configurations using the SEL-2600 and the SEL-2030. 
Contact SEL for help in applying these products in other configurations.

Program the SEL-2030 to perform four automated steps:

Step 1.

Receive temperature data from the SEL-2600.

Step 2.

Store the temperature data in memory.

Step 3.

Perform temperature threshold comparisons.

Step 4.

Issue control commands to a protective relay based on the 
temperature comparisons.

The next few pages describe how to configure the SEL-2030 to perform the 

four automated steps shown above. It is assumed that the SEL-2600 is connected to 
Serial Port 4 of the SEL-2030. Refer to the SEL-2030 Communications Processor 
Reference Manual 
and the SEL-2030 Communications Processor User’s Guide for 
further information on programming concepts.

Receive Temperature Data

Connect the SEL-2600 to the SEL-2030 using an SEL-2800 Fiber-Optic 

Transceiver and fiber-optic cable C801FD. Set the port settings of the SEL-2030 
as shown.

SET  P 4

DEVICE  = S
CONFIG  = N
PORTID  = SEL-2600 RTD Module
BAUD    = 2400
DATABIT = 8
STOPBIT = 1
PARITY  = N
RTS_CTS = N
XON_XOFF= N
TIMEOUT = OFF

Содержание SEL-2600

















Отзывы: