T
R
O
U
B
L
E
S
H
O
O
T
IN
G
※ For any troubles other than the above, consult the
retailer from whom the watch was purchased or SEIKO
CUSTOMER SERVICE CENTER.
Solution
This condition will be corrected when the watch is returned to a normal temperature.
If the watch does not return to its original condition, consult the retailer from whom the watch was purchased.
Check the time zone and reselect it.
For details, refer to the “List of Time Zones （p.53）.”
When a mark
is displayed near the time zone display and above the time
display in efficiency mode, Daylight Saving Time has been set.
If the setting of Daylight Saving Time is not required, change the setting to OFF.
For details, refer to “Time Zone Adjustment（p.52）.”
To prevent pressing the button by mistake, the button C has a roof.
Be aware that the button C has a harder-to-press construction than other buttons.
Refer to the illustrations near each operating instruction or “Button C （p.45）” to prevent
your finger or nail from being caught in the roof.
If the time for which the buttons were simultaneously pressed is 3 seconds or more, system
reset can be performed. It is not required to start pressing all the buttons simultaneously.
For details, refer to “How to Reset the System （p.68）.”
When releasing the buttons, release the button C last.
For details, refer to “How to Reset the System （p.68）.”
In time setting or time zone setting operation, when 2 minutes have elapsed
since the last button pressing, a timeout will occur and the status will return
to the time display. After waiting until that status, retry the operation.
Confirm the battery life indicator mark.
For details, refer to the “Battery Life Indicating Function （p.61）.”
Contact the retailer from whom the watch was purchased to
have the battery replaced with a new one.
Consult the retailer from whom the watch was purchased.
67
T
R
O
U
B
L
E
S
H
O
O
T
IN
G
Troubleshooting
Trouble
Probable Cause
Accuracy
The watch temporarily
gains or loses time.
The watch has been left in an extremely high
or low temperature for an extended time.
The time displayed on
the watch is one hour
ahead or behind of the
current time.
The time zone which is
different from the one you
wish to display was selected.
Daylight Saving Time has
been set.
Operation
The button C cannot
be operated.
The button was not pressed
properly due to its hard-to-
press construction.
System reset cannot
be performed.
The three buttons were not
pressed simultaneously for
3 seconds or more.
The button C was not
released last.
You don’t know how
to operate in mid-
process.
・・・・・・・・・・・・・・・
No operation results when
any button is pressed.
The battery life is expiring.
Display
Nothing is displayed.
The battery is dead.
The watch displays
but has stopped.
Other
The glass is blurred and the blur
persists for an extended time.
Small amount of water has entered the watch
due to deterioration of the gasket, etc.
66
69
T
R
O
U
B
L
E
S
H
O
O
T
IN
G
※ When this display does not appear, system
reset has not been performed.
In that case, retry operation.
Display mode: Mystery mode
Time zone: Zulu
UTC/London
Time: Start at 12:00 a.m.
■ Screen after System Reset
When system reset is performed, the
screen will change to the display as
shown below and the watch will start to
move after the whole screen has flashed.
T
R
O
U
B
L
E
S
H
O
O
T
IN
G
Resetting the system
To prevent pressing the
button by mistake, the
button C has a roof.
Be aware that the
button C has a harder-
to-press construction
than other buttons.
■ How to Reset the System
If abnormal movement occurs, reset the system
by the following operation:
Adjusting the time zone
Setting the Time
Check the time zone and adjust it.
→ How to Adjust the Time Zone （p.56）
Check the time and set it.
→ How to Set the Time （p.50）
When system reset is performed, the screen will change to
the display on the page 69 and the watch will start to move
after the whole screen has flashed.
Display mode: Mystery mode
Time zone: Zulu: UTC/London
Time: Start at 12:00 a.m.
B
C
A
Keep pressing all the
buttons simultaneously
for 3 seconds or more
and release them.
When releasing
the buttons,
release the
button C last.
68
In Case of Abnormal Movement
Button C
※ If the time for which the buttons were pressed simultaneously
is 3 seconds or more, system reset can be performed. It is
not required to start pressing all the buttons simultaneously.
Содержание SRXG001
Страница 1: ...http www seiko watch co jp ...
